manualshive.com logo in svg

Toro LX Lawn Tractor, Руководство по обслуживанию

Поделиться
Скачать
Toro LX Lawn Tractor Скачать руководство пользователя страница 186

MOWER DECK

7-32

 

LX Lawn Tractor Service Manual

7

7.  Install 3 self-tapping screws to secure the right 

mower deck cover to the mower deck (Fig. 665).

 

Fig 665

 PICT-7852

6.  Position the right mower deck belt cover (Fig. 664).

 

Fig 664

 PICT-7852

9.  Route the upper mower deck belt around the upper 

pulley of the double pulley spindle assembly. Tilt 
both idler pulleys and route the upper mower deck 
belt around the pulleys. Refer to the deck routing 
decal located on the mower deck (Fig. 667).

 

Fig 667

 PICT-7883

8.  Install the return spring into the top hole on the right 

side mower deck belt cover and the brake bracket 
pin (Fig. 666).

 

Fig 666

 PICT-7851

A.  Spring removal tool (Toro P/N 92-5771)

A

A

Содержание LX Lawn Tractor













































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды