manualshive.com logo in svg

Toro LX Lawn Tractor, Руководство по обслуживанию

Поделиться
Скачать
Toro LX Lawn Tractor Скачать руководство пользователя страница 222

MOWER DECK

7-68

 

LX Lawn Tractor Service Manual

7

5.  Place blocks under the mower deck to raise it up.

6.  Slide the front adjustment deck rod into the deck 

hanger bracket on the front of the mower deck (Fig. 
806).

 

Fig 806

 PICT-9681

7.  Lower the lift lever to the lowest height-of-cut setting 

(Fig. 807).

 

Fig 807

 PICT-9664

10.  Push the PTO idler pulley and bracket towards the 

rear of the machine (Fig. 809).

8.  Slide the mower deck toward the rear of the tractor 

so the deck pins line up with the deck lift arms.

9.  Pull the rear right and left deck support pins outward 

and position the rear deck hanger bracket holes 
inline with the pins. Release the pins to secure the 
rear of the mower deck (Fig. 808).

 

Fig 809

 PICT-9673

 

Fig 808

 PICT-9676

Содержание LX Lawn Tractor













































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды