Toro LX Lawn Tractor Скачать руководство пользователя страница 171

Страница: 171 / 236

MOWER DECK

7-17

LX Lawn Tractor Service Manual

3. Install the shoulder bolt between the brake bracket

and the right hand idler bracket. Tighten the bolt and
nut (Fig. 606).

5. Install the extension spring between the brake arm

and the right hand side belt cover (Fig. 608).

Note: The extension spring installs in the upper

hole on the belt cover.

Fig 606

PICT-7888

Fig 608

PICT-7851

4. Install the extension spring between the left and right

idler brackets (Fig. 607).

Fig 607

PICT-7854

2. Install the shoulder bolt and nut through the right

hand idler bracket and the mower deck (Fig. 605).

Note: Make sure the lower mower belt is routed

to the inside of the right hand idler bracket
assembly where it is mounted to the mower
deck.

Fig 605

PICT-7886

A. Spring removal tool (Toro P/N 92-5771)

Содержание LX Lawn Tractor













































































































































































































































Результаты поиска

Содержание LX Lawn Tractor

Отзывы:

Бренды по названию

Популярные бренды

Toro LX Lawn Tractor, Руководство по обслуживанию

Результаты поиска

Содержание LX Lawn Tractor

Отзывы:

Бренды по названию

Популярные бренды