manualshive.com logo in svg

Toro LX Lawn Tractor, Руководство по обслуживанию

Поделиться
Скачать
Toro LX Lawn Tractor Скачать руководство пользователя страница 148

HYDROSTATIC DRIVE SYSTEM

6-8

 

LX Lawn Tractor Service Manual

6

Note:  Line up the top two holes in the bracket with 

the bottom two holes in the frame (Fig. 514).

4.  Position a transaxle spacer between the frame and 

the axle housing, lining it up with the middle set of 
holes on the axle housing. Repeat on opposite side 
(Fig. 516).

 

Fig 514

 PICT-7572

 

Fig 516

 PICT-7575

5.  Insert the 4 mounting bolts (2 on each side) down 

through the mounting bracket, frame, spacer and 
axle housing holes (Fig. 517).

3.  Place a transmission mounting bracket on top of the 

frame, lining it up with the transmission mounting 
holes (Fig. 515).

 

Fig 517

 PICT-7576

 

Fig 515

 PICT-7574

Содержание LX Lawn Tractor













































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды