manualshive.com logo in svg

Toro LX Lawn Tractor, Руководство по обслуживанию

Поделиться
Скачать
Toro LX Lawn Tractor Скачать руководство пользователя страница 89

CHASSIS

3-75

LX Lawn Tractor Service Manual 

3

 

Fig 295

 PICT-7595

8.  Remove tension from the center double idler bracket 

and install the transmission drive belt around the 
idlers (Fig. 295).

 

Fig 294

 PICT-7594

7.  Route the transmission drive belt around the fi xed 

V-idler pulley (Fig. 294).

 

Fig 293

 PICT-7328

6.  Install a bolt and washer to secure the engine pulley 

to the crankshaft and torque to 37.5 to 50 ft-lbs. 
(50.84 to 67.79 Nm) (Fig. 293).

 

Fig 292

 PICT-7590

5.  Align the key of the engine pulley with the keyway 

on the crankshaft. Slide the engine pulley onto the 
crankshaft and install the transmission belt onto the 
pulley (Fig. 292).

Содержание LX Lawn Tractor













































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды