manualshive.com logo in svg

Toro LX Lawn Tractor, Руководство по обслуживанию

Поделиться
Скачать
Toro LX Lawn Tractor Скачать руководство пользователя страница 80

CHASSIS

3-66

 

LX Lawn Tractor Service Manual

3

 

Fig 258

 PICT-7318

7.  Install the rod end of the keeper rod into the frame. 

Secure the keeper rod by installing a bolt through 
the loop end and into the frame (Fig. 258).

 

Fig 260

 PICT-7332

9.  Route the belt around the double idler pulleys (Fig. 

260).

 

Fig 259

 PICT-7331

10. 

Electric PTO models:

  Install the electric PTO 

clutch onto the crankshaft. Refer to “Electric PTO 
Clutch Replacement - Installation” on page 3-28.

11.  Lower the machine.

12.  Install the upper transmission drive belt. See “Upper 

Transmission Drive Belt Replacement - Installation” 
on page 3-69.

13.  Install the mower deck:  42” deck on page 7-67; 46” 

deck on page 7-72; 50” deck on page 7-76.

8.  Install the belt guide (bolt and spacer) to the frame 

through the steering support bracket. Ensure the belt 
is routed to the right of the belt guide (Fig. 259).

Содержание LX Lawn Tractor













































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды