manualshive.com logo in svg

Toro LX Lawn Tractor, Руководство по обслуживанию

Поделиться
Скачать
Toro LX Lawn Tractor Скачать руководство пользователя страница 91

CHASSIS

3-77

LX Lawn Tractor Service Manual 

3

15.  Purge the system. Refer to “Purging the System” on 

page 3-82.

16.  Check the neutral adjustment. Refer to “Neutral 

Adjustment” on page 3-84.

17.  Check the brake adjustment. Refer to “Brake Adjust-

ment” on page 3-91.

 

Fig 300

 PICT-7494

14.  Connect the negative battery cable (Fig. 300).

 

Fig 301

 PICT-7109a

1.  Disconnect the negative battery cable and then the 

positive battery cable.

2.  Remove the battery hold down strap (Fig. 301).

The mower deck has been removed for photo purposes.

Removal

Variable Speed Pulley Replacement

 

Fig 302

 PICT-7276

3.  Remove the battery from battery compartment (Fig. 

302).

Содержание LX Lawn Tractor













































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды