background image

READ THROUGH THIS MANUAL BEFORE STARTING CONSTRUCTION. IT CONTAINS IMPORTANT INSTRUCTIONS AND WARNINGS CONCERNING THE ASSEMBLY AND USE OF THIS MODEL.

TOPA0714

WARRANTY

Top Flite Models guarantees this kit to be free from defects in both material and workmanship at the date of 
purchase. This warranty does not cover any component parts damaged by use or modification. 

In no case 

shall Top Flite’s liability exceed the original cost of the purchased kit.

 Further, Top Flite reserves the 

right to change or modify this warranty without notice.

In that Top Flite has no control over the final assembly or material used for final assembly, no liability shall be 
assumed nor accepted for any damage resulting from the use by the user of the final user-assembled prod-
uct. By the act of using the user-assembled product, the user accepts all resulting liability.

If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is 
advised to return this kit immediately in new and unused condition to the place of purchase.

To make a warranty claim send the
defective part or item to Hobby
Services at this address:

Include a letter stating your name, return shipping address, as much contact information as possible (daytime 
telephone number, fax number, e-mail address), a detailed description of the problem and a photocopy of the 
purchase receipt. Upon receipt of the package the problem will be evaluated as quickly as possible.

Hobby Services

3002 N. Apollo Dr. Suite 1
Champaign IL  61822  USA

SPECIFICATIONS

© 2015 

Top Flite, a Hobbico

®

 company.

Wingspan:

85 in [ 2160 mm]

Wing Area:

1329 sq in [85.7 dm

2

Weight:

19.5 – 21.5 lb [8842 – 9749 g]

Wing

Loading:

34 – 37 oz/sq ft
[104 –113 g/dm

2

]

Length:

75 in [1905 mm]

Radio:

5-8 channel

Engine:

2.6 – 4.0 cu in
[43 – 65 cc] spark ignition gas

Elec. Motor:

RimFire 65 cc  80-85-160kV

Flight

Battery:

12S 5000 mAh

[email protected]

Top Flite Models  Champaign, IL

Telephone (217) 398-8970, Ext. 5

INSTRUCTION MANUAL

Содержание P-47 Razorback









































Отзывы: