manualshive.com logo in svg

TM RACING 2012 TM 100 MX, Руководство пользователя и по обслуживанию

Поделиться
Скачать
TM RACING 2012 TM 100 MX Скачать руководство пользователя страница 69

ENGLISH

ENGLISH

69

TROUBLESHOOTING

If you have the envisioned maintenance operations carried out on your motorcycle, you will have very few problems. If, however, a 

problem does occur, please look for it in the following table and try to solve it. Please note that a lot of the operations cannot be carried 

out without the help of technicians . If in doubt, please contact an authorised TM dealer.

TROUBLESHOOTING

CAUSE

SOLUTION

PROBLEM

The motorcycle hasn’t been used for a while, therefo

-

re the old fuel has remained in thecarburetor bowl

Fuel supply interrupted

Engine flooded
Spark plug blackened or wet
Incorrect spark plug electrodes gap 

Spark plug cover or spark plug damaged

Oxidised CDI unit, pickup orcoil connectors

 
Water in the carburetor or clogged jets

The volatile fuel components evaporate easily. If the motorcycle 
has not been used for more than 1 week,  the old fuel  should 
be emptied from the carburetor bowl. When the bowl has been 
filled with fresh fuel, the engine will start immediately.

Disconnect the fuel hose from the carburetor, place it in a con

-

tainer and open the fuel tap,
-  if fuel escapes, clean the carburetor
-  if fuel does not escape, control the tank vent pipe or clean the 

fuel tap

Use the “by-pass” command as explained in the “Operating controls” chapter.

Clean and dry the spark plug or replace it.

Adjust the gap between the electrodes as shown in the tables

Slide off the spark plug cover, unscrew the spark plug, put the 
cover back onto the spark plug and, gripping the cover, keep 
the threaded part of the spark plug in contact with the head of 

the engine.

Turn the engine with the electric starter or pedal, a spark should 
appear between the electrodes of the spark plug
-  if the spark plug does not produce a spark, it must be repla

-

ced

-  if there is still no spark, remove the spark plug cover from the  

H.T. cable coming from the coil, hold it at a distance of about  
5 mm from the head and operate the starting system 

-  if there is a spark, replace the spark plug cover
-  if there is still no spark, check the ignition system 
Remove the saddle, the left side panel and the fuel tank, clean 
the connectors and treat them with a contact spray.
Disassemble and clean the carburetor

THE ENGINE

 DOES NOT START 

Содержание 2012 TM 100 MX





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды