TM RACING 2012 TM 100 MX Скачать руководство пользователя страница 16

Страница: 16 / 84

ENGLISH

SIDE STAND

Push the side stand to the floor using the foot and rest the motorcycle on

it. Pay attention that the ground is solid and the position stable.

SIDE STAND FIXING FOR OFF-ROAD ROUTES

If you drive the motorcycle off-road, the closed side stand can be ad

ditionally fixed using a rubber band (1).

FORK COMPRESSION ADJUSTMENT

The hydraulic brake system determines the behaviour of the fork in the

in compression stroke. The degree of hydraulic dampening in compres

sion can be adjusted on the basis of pilot preferences and/or hardness

of the spring installed.

MARZOCCHI USD FORK

There is an adjusting screw (2) on the fork cover. Operate using a screw

driver. Turning the screw clockwise the dampening increases, turning it

anticlockwise the dampening decreases. A total of 28 clicks

Never turn

the side screw (3).

WARNING

DO NOT OPERATE ON THE RED HEXAGONAL NUT (4) BECAUSE

IT DOES NOT CHANGE THE SPRING PRELOAD.

PAIOLI USD FORK (85/100 only)

Remove the rubber hood (5) located in the lower part of the fork leg and

turn the adjustment screw (6) using a screwdriver. By turning the screw

clockwise, dampening increases, turning it anticlockwise the dampening

decreases. A total of 26 clicks are available.

WARNING

BEFORE STARTING IT IS ADVISED TO TIGHTEN THE ADJUSTER FROM THE

STANDARD POSITION TO THE “TOTALLY CLOSED” POSITION AND COUNT

THE NOTCHES DETECTED SO THAT THE STANDARD POSITION CAN BE

RESTORED. FOR CONVENTION, THE NOTCHES ARE INDICATED FROM

THE “TOTALLY CLOSED” POSITION.

BOTH LEGS MUST HAVE THE SAME ADJUSTMENT.

OPERATING CONTROLS

Содержание 2012 TM 100 MX





















































































Результаты поиска

Содержание 2012 TM 100 MX

Отзывы:

Бренды по названию

Популярные бренды

TM RACING 2012 TM 100 MX, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание 2012 TM 100 MX

Отзывы:

Бренды по названию

Популярные бренды