TM RACING 2012 TM 100 MX Скачать руководство пользователя страница 52

Страница: 52 / 84

ENGLISH

DISASSEMBLY AND ASSEMBLY OF REAR

WHEEL (SMM)

Rest the motorcycle with the frame cradle on a stand, in a way that the

rear wheel does not touch the ground. Cut the safety binding (1), slide

out the clasp (2) and unscrew the wheel nut M50x1.5 (3). Pay attention

to the conical shim (4) placed between the nut and ring. Extract the

wheel carefully.

WARNING

- WHEN THE WHEEL NUT IS DISASSEMBLED, THE SHAFT AND NUT

THREADS MUST BE CLEANED CAREFULLY. RE-GREASE THEM TO PRE-

VENT SEIZING OF THE THREADS.

To assemble, proceed in the opposite direction, tightening the M50x1.5

wheel nut at 185 Nm. Remount the clasp and re-make the safety bind

ing.

- DO NOT FORGET TO CARRY OUT THE SAFETY BINDING AT THE ENDS

OF THE CLASP

- IF YOU DO NOT HAVE A DYNAMOMETRIC WRENCH WHEN MOUNTING,

HAVE THE TIGHTENING TORQUE CHECKED AS SOON AS POSSIBLE IN

A SPECIALISED TM WORKSHOP. A LOOSE WHEEL AXLE CAN CAUSE

UNSTABLE DRIVING.

- THE BRAKE DISC MUST ALWAYS BE PERFECTLY CLEAN FROM OIL

AND GREASE. ON THE CONTRARY, THE BRAKING EFFECT WOULD BE

GREATLY REDUCED.

- AFTER HAVING RE-ASSEMBLED THE REAR WHEEL ALWAYS ACTI-

VATE THE BRAKE PEDAL SO THAT THE PADS ADHERE TO THE DISC

AGAIN.

CHECK SPOKE TENSION

Correct tension of the spokes is very important for the stability of the

wheel and therefore safety on the road. An insufficiently taught spoke

leads to unbalancing of the wheel and in brief time loosening of other

spokes. Regularly check the tension of the spokes, particularly on new

motorcycles. Briefly hit every spoke with the end of a screwdriver (see

photo): the spoke should produce a clear sound. Hollow sounds mean

loose spokes. In this case you must have the spokes adjusted in a spe

cialised workshop. The wheel must also be centred.

- IF YOU CONTINUE TRAVELLING WITH INSUFFICIENTLY TIGHT SPOKES,

THEY MAY TEAR CAUSING PROBLEMS OF INSTABILITY.

- EXCESSIVELY TIGHT SPOKES MAY TEAR DUE TO LOCAL OVERLOAD-

ING.

DANGER

FRAME AND ENGINE MAINTENANCE

Содержание 2012 TM 100 MX





















































































Результаты поиска

Содержание 2012 TM 100 MX

Отзывы:

Похожие инструкции для 2012 TM 100 MX

Бренды по названию

Популярные бренды

TM RACING 2012 TM 100 MX, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание 2012 TM 100 MX

Отзывы:

Похожие инструкции для 2012 TM 100 MX

Бренды по названию

Популярные бренды