TM RACING 2012 TM 100 MX Скачать руководство пользователя страница 39

Страница: 39 / 84

ENGLISH

TELESCOPIC FORK VENT SCREWS

Every 5 hours of use in competition it is necessary to release the the

air-pressure from inside the fork.

The Marzocchi fork features a tyre valve (1) protected by a rubber cap

(2). Remove the rubber cap and press gently the valve stem.

On the 85 and 100 models, loosen by some turns the bleeding screws

(3) located on the top of the fork legs, thus allowing the air-pressure to

bleed.

Before operating on the screws or on the valve, lift the motorcycle onto

the stand in a way that the front wheel does not touch the ground. If the

motorcycle is used mainly on roads, it is sufficient only to carry out this

operation during periodical maintenance.

WARNING

VERY HIGH PRESSURE INSIDE THE FORK CAN CAUSE THE FORK TO LEAK.

IF YOUR FORK PRESENTS A LEAK, LOOSEN THE VENT SCREWS BEFORE

HAVING THE SEALING ELEMENTS REPLACED.

CLEANING OF TELESCOPIC FORK DUST

SCRAPER

The dust scraper (4) must scrape the dust and dirt from the fork rods.

However, after some time, dirt may also reach behind the dust scrap

ers. If the dirt is not removed, the oil seal units, which are found behind,

may leak.

Use a screwdriver to lever the dust scraper from the outside legs and

push it downwards.

Clean the dust scraper, the outside legs and the rods carefully. Oil them

well with silicone spray or with engine oil. Finally, push the dust scraper

manually into the outside legs.

FRAME AND ENGINE MAINTENANCE

Содержание 2012 TM 100 MX





















































































Результаты поиска

Содержание 2012 TM 100 MX

Отзывы:

Бренды по названию

Популярные бренды

TM RACING 2012 TM 100 MX, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание 2012 TM 100 MX

Отзывы:

Бренды по названию

Популярные бренды