TM RACING 2012 TM 100 MX Скачать руководство пользователя страница 56

Страница: 56 / 84

ENGLISH

HALOGEN LIGHT (SMR)

LIGHT HEIGHT ADJUSTMENT

The front light height can be adjusted. First you need to move the rubber

stripes on the fork leg so as the light body sits horizontally, then you can

turn the front screw (1) the adjust the light height.

Turn the screw clockwise to lift the light, anticlockwise to lower it.

REPLACEMENT OF HEADLIGHT/POSITION LIGHT BULB

Release both rubber stripes and move the light-holder mask forward.

HEADLIGHT TWO-LIGHT BULB

Disconnect the cables connector and remove the rubber protection (2).

Release the retainer and carefully extract the halogen bulb (3).

Reassemble the new bulb, the rubber protection and the connector.

POSITION BULB

Disconnect the side connector, extract the bulb-holder (4) from the light

body and change the bulb. Reassemble the bulb-holder.Reposition the

light-holder mask and secure it with rubber stripes.

WARNING

NEVER TOUCH THE GLASS BULB, TO PREVENT LEAVING TRACES OF

GREASE.

TO BE SURE OF INSERTING THE ESTABLISHED BULBS, CONSULT THE
“CYCLE PART TECHNICAL DATA” TABLE

FRAME AND ENGINE MAINTENANCE

Содержание 2012 TM 100 MX





















































































Результаты поиска

Содержание 2012 TM 100 MX

Отзывы:

Бренды по названию

Популярные бренды

TM RACING 2012 TM 100 MX, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание 2012 TM 100 MX

Отзывы:

Бренды по названию

Популярные бренды