TM RACING 2012 TM 100 MX Скачать руководство пользователя страница 10

Страница: 10 / 84

ENGLISH

OPERATING CONTROLS

CLUTCH LEVER BREMBO PUMP

The Brembo clutch pump is visibile in the picture with n. 1

The clutch lever (2) is located on the left side of the handlebar.

With this option, to adjust the clutch lever distance from the handlebar

grip (see maintenance operation), you have to turn the adjustment knob

(3).

Rotate clockwise to increase the distance or counterclockwise to de

crease the distance.

FRONT BRAKE LEVER NISSIN PUMP (END/MX)

The front brake pump lever (4) is located on the right side of the handlebar

and activates the front wheel brake.

The distance of the front brak lever from the handlebar grip can be

adjusted through the adjustment screw (5) (see “Frame and Engine

Maintenance” chapter”).

FRONT BRAKE LEVER BREMBO RADIAL PUMP

(SMR/SMM)

The front brake pump lever (6) is located on the right side of the handle

bar and activates the front wheel brake. The distance of the brake lever

from the handlebar grip can be adjusted through the adjustment knob

(7) (see “Frame and Engine Maintenance” chapter)

Содержание 2012 TM 100 MX





















































































Результаты поиска

Содержание 2012 TM 100 MX

Отзывы:

Похожие инструкции для 2012 TM 100 MX

Бренды по названию

Популярные бренды

TM RACING 2012 TM 100 MX, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание 2012 TM 100 MX

Отзывы:

Похожие инструкции для 2012 TM 100 MX

Бренды по названию

Популярные бренды