TM RACING 2012 TM 100 MX Скачать руководство пользователя страница 42

Страница: 42 / 84

ENGLISH

REPLACEMENT OF FORK SPRINGS

If your body weight is less than 70 kg or exceeds 80 kg, adequate fork

springs must be used.

If you are in doubt or have any questions, please contact your authorised

TM dealer.

According to our experience, the dampening grade in compression can

remain unvaried. With a softer spring, the dampening grade in rebound

can be reduced by some clicks, with a harder spring, increased by some

clicks.

WARNING

FOR FURTHER AND MORE DETAILED INFORMATION REGARDING THE

FORK REFER TO THE INSTRUCTION BOOK SUPPLIED BY THE MANUFAC-

TURER OF THE FORK AND GIVEN BY TM ACCOMPANYING THE MOTOR-
CYCLE.

VARIATION OF REAR SHOCK SPRING PRELOAD

The preload of the spring can be varied by turning the adjustment ring

nut (1) (4) (6). With this aim, it is advised to disassemble the rear shock

and clean it well before operating.

INDICATION:

- Before varying the spring preload you should take note of te basic

adjustment - e.g. how many thread turns are visible above the lock

ring nut (6).

- By 1 turn of the adjustment ring nut (1) (4) (6) the spring pre-load varies

by 1.5 mm.

SACHS

Loosen the lock ring nut (2) and turn the adjustment ring nut (1). Turning

it anticlockwise (viewed from the top) the preload decreases, turning it

clockwise (viewed from the top) the preload increases.

After the adjustment, tighten the lock ring nut (6).

OHLINS

Loosen the clamp (3) using a 4mm. Allen wrench and turn the adjust

ment ring nut (4). Turning it anticlockwise (viewed from the top) the

preload decreases, turning it clockwise (viewed from the top) the preload

increases.

Tighten the clamp closure (3) after adjustment.

The Junior model has an Ohlins shock absorber with double nut adjust

ment.

By mean of a 4mm. Allen wrench loosen the locking screw (5) of the ring

nut (6) and turn the ring nut itself.

By turning it anticlockwise (seen from the top) the preload decreases,

turning it clockwise the preload increases.

Tighten the locking screw after the adjustment.

FRAME AND ENGINE MAINTENANCE

Содержание 2012 TM 100 MX





















































































Результаты поиска

Содержание 2012 TM 100 MX

Отзывы:

Бренды по названию

Популярные бренды

TM RACING 2012 TM 100 MX, Руководство пользователя и по обслуживанию

Результаты поиска

Содержание 2012 TM 100 MX

Отзывы:

Бренды по названию

Популярные бренды