Thrush Aircraft S2RHG-T65 TURBO THRUSH Скачать руководство пользователя

Страница: 172 / 272

THRUSH AIRCRAFT, INC – MODEL S2RHG-T65 TURBO THRUSH

AIRCRAFT MAINTENANCE MANUAL

Effective: 5/05/04

7-21

PROBLEM CAUSE

REMEDY

FLAP SYSTEM (Continued)

Flaps do not extend
(down) or retract (up).
(Cont.)

Defective microswitch.

Replace microswitch.

Flaps fail to retract (up)
completely.

Incorrect rigging of push
rods.

Rig in accordance with rigging
procedures.

Flaps fail to extend
(down) completely.

Incorrect rigging of push
rods.

Rig in accordance with rigging
procedures.

Flaps not synchronized
or fail to fit evenly when
retracted (up).

Incorrect adjustment of
push rods.

Adjust in accordance with
rigging procedures.

Bent push rods.

Straighten or replace.

Bent flap.

Repair or replace flap.

Flaps on one side fail to
operate.

Broken arm on torque
tube or broken push rod.

Replace broken parts.

Disconnected push rod.

Connect push rod and recheck
rigging procedures.

RUDDER SYSTEM

Lost motion between
rudder pedals and
rudder.

Cables loose.

Adjust in accordance with
rigging procedures.

Broken pulley.

Replace pulley.

Lost motion between
rudder pedals and
rudder.

Bolts attaching rudder
horn to rudder loose.

Tighten bolts.

Excessive resistance to
rudder pedal movement.

Cables too tight.

Adjust cables in accordance
with rigging procedures.

Pulleys binding or
rubbing.

Provide proper clearance if
pulleys are rubbing pulley
brackets or cable guards.

Содержание S2RHG-T65 TURBO THRUSH

















































































































































































































































































Результаты поиска

Содержание S2RHG-T65 TURBO THRUSH

Отзывы:

Похожие инструкции для S2RHG-T65 TURBO THRUSH

Бренды по названию

Популярные бренды

Thrush Aircraft S2RHG-T65 TURBO THRUSH, Руководство по обслуживанию

Результаты поиска

Содержание S2RHG-T65 TURBO THRUSH

Отзывы:

Похожие инструкции для S2RHG-T65 TURBO THRUSH

Бренды по названию

Популярные бренды