Thrush Aircraft S2RHG-T65 TURBO THRUSH Скачать руководство пользователя страница 110 | Manualshive

Страница: 110 / 272

background image

THRUSH AIRCRAFT INC – MODEL S2RHG-T34 TURBO THRUSH

AIRCRAFT MAINTENANCE MANUAL

5-6

Effective: 5/05/04

B.

Remove drain plug and drain pump.

C.

Disconnect electrical connector from motor.

D.

Remove hose from pump and cap hose.

E. Remove

attaching

hardware and remove pump assembly from support bracket.

AUXILIARY ELECTRIC FUEL PUMP INSTALLATION

A.

Install pump to support brackets and tighten hardware.

B.

Connect hose to pump

C. Open

fuel

shutoff valve.

D. Connect

electrical

connector to pump motor.

E.

Operate fuel pump and check for fuel leaks at lines and fittings.

ENGINE-DRIVEN FUEL PUMP

The engine-driven fuel pump installed on the lower right rear portion of the engine is
provided with a relief valve that will allow fuel to pass through from the airframe pump to
the engine in the event of pump failure.

FUEL FILTER

The fuel strainer in the filter should be removed, inspected and cleaned every 100 hours
of operation or sooner if improper fuel circulation is suspected. (See Figure 5-1 and 5-2
fuel filter.)

AIRBORNE 1J18 FUEL FILTER SERVICE INSTRUCTIONS

** CAUTION **

The following procedures must be followed in the order of

steps given to avoid damage to the components and to

assure proper functioning of the unit.

Refer to Figure 5-2 for identification of parts during disassembly and re-assembly.

A.

Turn airframe fuel shutoff valve to “OFF” position. Cut, remove and discard safety
wire (not shown) securing filter bowl assembly.

B.

Using 13/16” wrench unscrew hex nut, (Item 1) bowl retainer. (

Right

hand

threads.)

C.

Pull filter bowl (Item 2) straight off filter housing stud.

D.

Using one thin ½” open end wrench, hold filter retaining nut (Item 3) while
loosening jam nut (Item 4) with second ½” wrench.

«
...
108
109
110
111
112
...
»

Содержание S2RHG-T65 TURBO THRUSH

















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S2RHG-T65 TURBO THRUSH

Бренд: Helio Страницы: 28

Бренд: STEMME Страницы: 236

Бренд: Beechcraft Страницы: 9

Бренд: Beechcraft Страницы: 668

Бренд: Sky Country Страницы: 21

Бренд: MAC PARA Страницы: 40

Бренд: Quantum Страницы: 168

Бренд: Way Страницы: 16

Бренд: TAKOON Страницы: 30

Бренд: Hobbico Страницы: 20

Бренд: DAVINCI GLIDERS Страницы: 15

Бренд: FLYSURFER Страницы: 16

Бренд: FLYSURFER Страницы: 20

Бренд: FLYSURFER Страницы: 28

Infinity 2.0 Bar

Бренд: FLYSURFER Страницы: 47

Бренд: FLYSURFER Страницы: 68

Бренд: EScale Страницы: 16

Бренд: Dudek Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды