Thrush Aircraft S2RHG-T65 TURBO THRUSH Скачать руководство пользователя страница 115

Страница: 115 / 272

THRUSH AIRCRAFT, INC – MODEL S2RHG-T65 TURBO THRUSH

AIRCRAFT MAINTENANCE MANUAL

Effective: 5/05/04

5-11

PROBLEM PROBABLE

CAUSE

REMEDY

No fuel quantity
indication.
(Continued)

Left and right fuel
quantity indicator switch
defective.

Check continuity and replace if defective.

No power to gauge.

Check power to gauge. If no power,
check for defective circuit breaker.

Power, ground and
transmitter checks
good.

Circuit board on rear of gauge defective.
(Replace board) or entire gauge.

Fuel indicated
full at all times.

Open ground between
gauge and transmitter.

Check ohms to transmitter. Check for
broken wire. Transmitter should read 0
ohms when fuel tank is empty and 33
ohms when fuel tank is full.

No fuel flow to
engine-driven
fuel pump.

Fuel tanks empty.

Check fuel quantity. Service with proper
grade and amount of fuel.

Fuel line disconnected
or broken.

Inspect fuel lines. Connect or repair fuel
lines.

Header tank outlet fuel
strainers plugged.

Disconnect fuel lines from tank outlets.
No fuel indicates plugged strainers.
Remove and clean strainers and flush
out tanks.

Fuel filter element
plugged.

Inspect filter element. Clean or replace
filter element.

Fuel line plugged.

Starting at fuel pump inlet, disconnect
fuel lines successively until plugged line
is located. Clean out or replace fuel line.

Fuel starvation
after starting.

Partial fuel flow from the
preceding causes.

Use the preceding isolation procedures,
checking for sufficient rate of flow. Using
the preceding remedies.

Malfunction of engine-
driven fuel pump.

Check pump outlet during starting.
Replace fuel pump. See Section IV.

Fuel vents plugged.

Pressure check each vent line. Clean or
replace vent line.

No fuel flow
when auxiliary
pump is turned
on.

Defective electric
auxiliary fuel pump
switch.

Check continuity of switch. Replace
defective switch.

Содержание S2RHG-T65 TURBO THRUSH

















































































































































































































































































Результаты поиска

Содержание S2RHG-T65 TURBO THRUSH

Отзывы:

Похожие инструкции для S2RHG-T65 TURBO THRUSH

Бренды по названию

Популярные бренды

Thrush Aircraft S2RHG-T65 TURBO THRUSH, Руководство по обслуживанию

Результаты поиска

Содержание S2RHG-T65 TURBO THRUSH

Отзывы:

Похожие инструкции для S2RHG-T65 TURBO THRUSH

Бренды по названию

Популярные бренды