manualshive.com logo in svg

Thrush Aircraft S2RHG-T65 TURBO THRUSH, Руководство по обслуживанию


Поделиться
Скачать
background image

THRUSH AIRCRAFT, INC – MODEL S2RHG-T65 TURBO THRUSH 

AIRCRAFT MAINTENANCE MANUAL

 

 

Effective: 05/05/04 

 

7-5 

bearing hinges and is attached to the aft wing spar at three points.  One balance weight is 
installed in the outboard leading edge of each aileron to prevent flutter. 

* NOTE * 

The left and right ailerons are not interchangeable.  There is 

a female locating slot approximately 25 ½ inches from the 

counterweight leading edge that must align with a male 

located tab in the aileron bay. 

The aileron control is driven by a single push rod from the control stick torque tube to a 
vertical bell crank at the right side of the fuselage (See Figure 7-2).  A short push rod 
connects the bell crank to a vertical idler in the left side of the fuselage.  In each wing, the 
inboard push tubes connect between the bell crank and idler in the fuselage to the aft side 
of a bell crank near the inboard end of the aileron.  From the forward side of this bell 
crank, the outboard push tube connects to the forward arm of the drive bell crank located 
at the aileron mid span.  The short arm of the drive bell crank is connected to a push rod 
that drives the aileron.  The ailerons are also connected to the rudder controls by spring-
loaded cables that enable the ailerons to be activated in conjunction with the rudder.  This 
provides a safety factor.  In case the aileron system becomes inoperative, the rudder 
system will lift the aileron. (Fig. 7-3) 

AILERON REMOVAL 

A. 

Disconnect push rod at aileron.  Do not change position of rod end on push rod. 

B. 

Remove aileron hinge bolts. 

C. 

Remove aileron from aircraft. 

AILERON INSTALLATION 

Installation of the aileron is the reverse of the removal procedure.  In the event push rod 
length has been altered, streamline trailing edge of opposite aileron with trailing edge of 
wing and flap and secure with a temporary lock.  Adjust push rod length to align attaching 
bolt hole with hole in aileron hinge fitting, when aileron is in neutral position.  Recheck 
aileron rigging. 

AILERON RIGGING 

Assure the ailerons are attached and the system push tubes are assembled, except for 
the two lateral push rods in the fuselage.  Ensure that flaps have been rigged.  Rig the 
ailerons as follows: 

A. 

Clamp the ailerons at the trailing edge of the wing tip in the neutral position.  
Ailerons are in neutral when ailerons are 1/8" below flap trailing edge. 

B. 

Adjust the length of the push rod from aileron outboard wing bell crank until 
inboard wing bell crank is perpendicular to the rear spar, both sides. This can be 
checked through the inspection holes just forward of the rear spar. 

Содержание S2RHG-T65 TURBO THRUSH

















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S2RHG-T65 TURBO THRUSH

Textron Cessna 208B Service Bulletin preview
Cessna 208B
Бренд: Textron Страницы: 34
NIVIUK GLIDERS SKIN 2 User Manual preview
SKIN 2
Бренд: NIVIUK GLIDERS Страницы: 25
Niviuk LINK 2 User Manual preview
LINK 2
Бренд: Niviuk Страницы: 27
Niviuk DOBERMANN 2 User Manual preview
DOBERMANN 2
Бренд: Niviuk Страницы: 24
BONANZA A-36 Instruction Manual preview
A-36
Бренд: BONANZA Страницы: 8
3D AEROWORKS VOUGHT F4U-1D CORSAIR Assembly Manual And User Manual preview
VOUGHT F4U-1D CORSAIR
Бренд: 3D AEROWORKS Страницы: 24
SKY PARAGLIDERS APOLLO 2 L User Manual preview
APOLLO 2 L
Бренд: SKY PARAGLIDERS Страницы: 36
MAC PARA MacJet User Manual preview
MacJet
Бренд: MAC PARA Страницы: 40
PAPILLON BODYGUARD 7 Manual preview
BODYGUARD 7
Бренд: PAPILLON Страницы: 52
Ozone Viper 3 Manual preview
Viper 3
Бренд: Ozone Страницы: 24
U-Turn BLACKLIGHT L Manual preview
BLACKLIGHT L
Бренд: U-Turn Страницы: 50
Zodiac Aerospace ATOM Legend S T1 Use And Maitain Manual preview
ATOM Legend S T1
Бренд: Zodiac Aerospace Страницы: 83
Textron Cessna Grand Caravan Ex 208B Pilot'S Operating Handbook And Faa Approved Airplane Flight Manual preview
Cessna Grand Caravan Ex 208B
Бренд: Textron Страницы: 846
Tutti Bambini GC 35 Assembly Instructions Manual preview
GC 35
Бренд: Tutti Bambini Страницы: 12
MAULE MX-7-180AC Airplane Flight Manual preview
MX-7-180AC
Бренд: MAULE Страницы: 29
MAULE MX-7-180A Airplane Flight Manual preview
MX-7-180A
Бренд: MAULE Страницы: 30
MAULE MX-7-180 Star Rocket Airplane Flight Manual preview
MX-7-180 Star Rocket
Бренд: MAULE Страницы: 30
MAULE M-7-260C Airplane Flight Manual preview
M-7-260C
Бренд: MAULE Страницы: 30

Бренды по названию

Популярные бренды

Загрузить еще бренды