Thrush Aircraft S2RHG-T65 TURBO THRUSH Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 272

background image

THRUSH AIRCRAFT, INC – MODEL S2RHG-T65 TURBO THRUSH

AIRCRAFT MAINTENANCE MANUAL

viii

Effective: 09/16/05

INTRODUCTION

This publication provides information for the Thrush Aircraft, Inc. Model S2RHG-T65
Turbo Thrush Aircraft. Installations or equipment will vary from model to model due to
the wide range of optional equipment. The information contained within this manual is
based on data available at the time of publication and will be kept current by changes or
service publications.

This manual contains information on aircraft systems and operating procedures required
for safe and effective maintenance. It shall not, however, be used as a substitute for
sound judgment.

In this manual:

*** WARNING ***

Indicates a strong possibility of severe personal injury or loss
of life if instructions are not followed.

** CAUTION **

Indicates a possibility of personal injury or equipment
damage if instructions are not followed.

*

NOTE

*

Gives helpful information.

** CAUTION **

Detailed descriptions of standard workshop procedures,
safety principles and service operations are NOT included in
this manual. Please note that this manual DOES contain
warnings and cautions against some specific service
methods which could cause PERSONAL INJURY or could
damage an aircraft or MAKE IT UNSAFE. Please
understand that these warnings cannot cover all conceivable
ways in which service, whether or not recommended by
Thrush Aircraft Inc., might be done or of the possible
hazardous consequences of each conceivable way, nor
could Thrush Aircraft Inc. investigate all such ways. Anyone
using service procedures or tools, whether or not
recommended by Thrush Aircraft Inc., must satisfy himself
thoroughly that neither personal safety nor aircraft safety will
be jeopardized.

Changes to this manual accomplished under the latest revision are marked with a solid
vertical line next to the change in the page margin. Formatting changes, minor wording
changes and correction of minor typographical errors are not marked as changes. If the
page is new or completely revised, only the effective date will be updated.

All information contained in this manual is based on the latest product information
available at the time of printing. We reserve the right to make changes at any time
without notice.

«
...
6
7
8
9
10
...
»

Содержание S2RHG-T65 TURBO THRUSH

















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S2RHG-T65 TURBO THRUSH

Бренд: Jabiru Страницы: 55

Бренд: Cessna Страницы: 192

Бренд: U-Turn Страницы: 30

Бренд: Ride Best Страницы: 14

Бренд: Air Design Страницы: 35

Бренд: Air Design Страницы: 38

RAST Mirage RS 2

Бренд: Swing Страницы: 4

Бренд: Swing Страницы: 48

Powerplay Scorpio

Бренд: Swing Страницы: 52

Бренд: 3D R Страницы: 23

Бренд: Jabiru Страницы: 171

Бренд: Trixy Aviation Страницы: 128

Бренд: ICARO Страницы: 37

Бренд: Delta Children Страницы: 7

EDGE 540T SMS Tabs

Бренд: RC-Xplanes Страницы: 10

Бренд: WINDTECH Страницы: 24

Бренд: Core Страницы: 2

Mini Warbirds Rare Bear

Бренд: skyangel Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды