Thrush Aircraft S2RHG-T65 TURBO THRUSH Скачать руководство пользователя страница 173

Страница: 173 / 272

THRUSH AIRCRAFT, INC – MODEL S2RHG-T65 TURBO THRUSH

AIRCRAFT MAINTENANCE MANUAL

7-22

Effective: 5/05/04

PROBLEM CAUSE

REMEDY

RUDDER SYSTEM (Continued)

Excessive resistance to
rudder pedal movement.
(Continued)

Rudder binding caused
by bent rudder horn.

Replace rudder horn.

Rudder pedal needs
lubrication.

Lubricate as required.

Cables not in place on
pulleys.

Install cables correctly.

Bent rudder.

Repair or replace rudder.

Rudder pedals not
neutral when rudder is
streamlined.

Rudder cables incorrectly
rigged.

Rig in accordance with rigging
procedures.

Incorrect rudder travel.

Rudder horn stops
incorrectly adjusted.

Adjust in accordance with
rudder rigging procedures.

ELEVATOR SYSTEM

Resistance to control
stick movement.

Pulley binding or rubbing.

Provide proper clearance if
rubbing pulley bracket or guard.

Binding control stick
bearings.

Lubricate bearings. Repair or
replace elevator horns.

Elevator hinges need
lubrication.

Lubricate hinges as required to
give free movement.

Incorrect elevator travel.

Elevator bellcrank, idler,
and push tubes
incorrectly adjusted.

Adjust in accordance with
rigging procedures.

Correct elevator travel
cannot be obtained by
adjusting bellcrank, idler
and push tubes.

Control stick stops
incorrectly rigged.

Adjust control stick stops in
accordance with rigging
procedures.

Содержание S2RHG-T65 TURBO THRUSH

















































































































































































































































































Результаты поиска

Содержание S2RHG-T65 TURBO THRUSH

Отзывы:

Похожие инструкции для S2RHG-T65 TURBO THRUSH

Бренды по названию

Популярные бренды

Thrush Aircraft S2RHG-T65 TURBO THRUSH, Руководство по обслуживанию

Результаты поиска

Содержание S2RHG-T65 TURBO THRUSH

Отзывы:

Похожие инструкции для S2RHG-T65 TURBO THRUSH

Бренды по названию

Популярные бренды