Thrush Aircraft S2RHG-T65 TURBO THRUSH Скачать руководство пользователя | Manualshive

Страница: 128 / 272

background image

THRUSH AIRCRAFT INC – MODEL S2RHG-T65 TURBO THRUSH

AIRCRAFT MAINTENANCE MANUAL

6-8

Effective: 5/25/05

1.

Bearing cup removal:

Heat wheel half in an oven not exceeding 212°F

for 15 minutes. Remove wheel half from heat source and immediately
remove bearing cup by carefully tapping out evenly from the inside with a
fiber drift.

2.

Bearing cup installation:

Place wheel half in oven not exceeding 212°F

for 15 minutes. Chill new bearing cup in an atmosphere of -25°F to -65°F
for no less than 4 hours. Chilling can also be accomplished by placing the
bearing cup in dry ice for a minimum of 15 minutes. Dry cup thoroughly
and installed chilled bearing cup into bore of heated wheel half using a
thin coat of zinc chromate primer as a lubricate/protectant. Tap gently into
place with fiber drift making sure bearing cup is evenly seated against
shoulder of wheel half. Avoid cocking bearing cup during installation. If
bearing cup will not seat properly in wheel half, repeat above said
procedures or replace wheel half assembly.

G.

Replace any wheel casting that is distorted, corroded, or has visible cracks.

TAIL WHEEL REASSEMBLY AND INSTALLATION (6.00 - 6 8pr)

To assemble and reinstall tail wheel, refer to Figure 6-1 and proceed as follows:

A.

Wipe tire and tube (serviceable or new) with denatured alcohol, followed by soap
and water, then dry thoroughly.

B.

Inflate the inner tube just enough to round it out, dust tube lightly with tube talc.

* NOTE *

Tires and tubes are balanced as individual units and marked
at time of manufacture. The tire balance mark is a red dot.
The tube balance mark is a yellow stripe on the base of the
tube. Always assemble tire and tube with marks aligned.

C.

Place tube in tire and align balance marks. If tube has no balance mark, place
valve stem adjacent to tire balance red dot.

D.

Install tire and tube on the wheel half containing the valve stem hole and then the
opposite.

E. Install

the

wheel

through-bolts with bolt heads opposite valve stem side, tighten

nuts evenly and torque to 150 inch-pounds.

*** WARNING ***

Uneven or improper torque may cause a bolt or wheel

failure. Inflate tire until tire beads are sealed, remove

schrader valve core, and allow tube to completely deflate.

Install the valve-core and inflate 6.00-6 8pr tire to 55 psi.

Assure schrader valve does not leak before replacing valve

cap.

«
...
126
127
128
129
130
...
»

Содержание S2RHG-T65 TURBO THRUSH

















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S2RHG-T65 TURBO THRUSH

Бренд: Van's Aircraft Страницы: 34

Бренд: Van's Aircraft Страницы: 222

Бренд: Pilatus Страницы: 222

Бренд: SPIDERKITES Страницы: 7

Бренд: Caution Santa Cruz Страницы: 8

Бренд: Nova Страницы: 40

Бренд: Beechcraft Страницы: 61

Бренд: Pelican Страницы: 32

Бренд: MINIPLANE Страницы: 15

Бренд: SKY PARAGLIDERS Страницы: 34

Бренд: MAC PARA Страницы: 32

Бренд: SKY PARAGLIDERS Страницы: 29

Samba R.E.S. Evo

Бренд: cad2cnc Страницы: 33

XS Monowheel Motorglider

Бренд: Europa Aircraft Страницы: 96

Edge XT 582-L Cruze

Бренд: AirBorne WindSports Страницы: 110

Бренд: Gin Gliders Страницы: 7

Бренд: GIN Kiteboarding Страницы: 15

Бренд: FLYSURFER Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды