Thrush Aircraft S2RHG-T65 TURBO THRUSH Скачать руководство пользователя | Manualshive

Страница: 125 / 272

background image

THRUSH AIRCRAFT, INC – MODEL S2RHG-T65 TURBO THRUSH

AIRCRAFT MAINTENANCE MANUAL

Effective: 9/16/05

6-5

D.

Inspect main spring leaf for corrosion and cracks. Replace leaf spring as
needed.

E.

Inspect spindle housing assembly welds for cracks.

F.

Inspect spindle housing assembly for cracks and corrosion.

G.

Inspect lock pin and upper and lower lock plates for wear, corrosion, cracks, and
proper operation.

H.

Inspect centering springs for corrosion, wear at ends, and for correct operation.

I.

Inspect lock pin flexible cable and spring for corrosion and correct operation.

J.

Inspect P/N95207-1 Acetal (Delrin®) lower support block spacer for wear and
cracks.

K.

Inspect upper and lower leaf spring support blocks, and attachment hardware for
wear, corrosion, and cracks. Ensure that the leaf spring support blocks grips the
leaf spring tightly to prevent leaf spring movement fwd. and aft. Ensure flexible
sealant around contact edges of support blocks, lower support block spacer and
leaf spring is intact to prevent collection of potential corrosive material in this
area. Lubricate 2 ea. Trunnion Zerk (grease) fittings with MIL-G-81322
(Aeroshell 22).

L.

Repair of the tail landing gear is limited to replacement of component parts,
bearings, bushings, smoothing out minor nicks and scratches, repainting chipped
or peeled areas.

DISASSEMBLY OF SPINDLE HOUSING ASSEMBLY

(See Figure 6-1)

M.

If desired, remove bolts, nuts and washers that bolt tail wheel fork to spindle.

N.

Remove bolts, nuts, and washers that bolt centering arm to top of spindle and
remove centering arm. Note orientation for proper reassembly.

O.

Remove red plastic cap plug (dustcover).

P.

Remove cotter pin, castellated nut, tongue washer, grease cup washer, and cone
bearing.

Q.

Remove spindle assembly and thrust washer from spindle housing. Do not
remove upper bearing cup or bottom bronze bushing unless replacement is
indicated by inspection.

CLEANING, INSPECTION AND REPAIR OF TAIL GEAR SPINDLE HOUSING

ASSEMBLY.

A.

Clean all parts with a suitable type cleaning solvent.

B.

Inspect all bolts, bearings and bushings for excessive wear, corrosion and
damage.

C.

Inspect spindle assembly for cracks, excessive wear, corrosion and damage.

D.

Inspect spindle housing for cracks, excessive wear, corrosion and damage.

«
...
123
124
125
126
127
...
»

Содержание S2RHG-T65 TURBO THRUSH

















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S2RHG-T65 TURBO THRUSH

Бренд: Zenith Страницы: 9

Бренд: Composite-ARF Страницы: 37

Бренд: Guimbal Страницы: 156

SKYLIGHT tourist

Бренд: SKY PARAGLIDERS Страницы: 45

Бренд: Ocean Rodeo Страницы: 15

SQUARE Light 90

Бренд: ICARO Страницы: 14

Бренд: Ozone Страницы: 12

Бренд: Ozone Страницы: 20

Бренд: Parajet Страницы: 8

Бренд: Magni Gyro Страницы: 115

PA-28RT-201T TURBO ARROW IV

Бренд: Piper Aircraft Corporation Страницы: 139

Cherokee Arrow II

Бренд: Piper Aircraft Corporation Страницы: 142

TWIN COMANCHE PA-30

Бренд: Piper Aircraft Corporation Страницы: 863

PA-28-161 CADET

Бренд: Piper Aircraft Corporation Страницы: 422

Cherokee PA-28-140

Бренд: Piper Aircraft Corporation Страницы: 26

Cherokee PA-28-180

Бренд: Piper Aircraft Corporation Страницы: 36

CHEYENNE PA-31T

Бренд: Piper Aircraft Corporation Страницы: 68

Бренд: Eurocopter Страницы: 376

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды