Thrush Aircraft S2RHG-T65 TURBO THRUSH Скачать руководство пользователя страница 171

Страница: 171 / 272

THRUSH AIRCRAFT, INC – MODEL S2RHG-T65 TURBO THRUSH

AIRCRAFT MAINTENANCE MANUAL

7-20

Effective: 5/05/04

CONTROL SYSTEM TROUBLESHOOTING CHART

AILERON SYSTEM

PROBLEM CAUSE

REMEDY

Resistance to control
stick movement.

Control stick bearings
dry or worn.

Check control stick bearings
for lubrication, excessive wear
and cleanliness.

Torque tube bearings
dry or worn.

Check bearing for lubrication,
excessive wear and
cleanliness.

Bent

aileron.

Repair or replace aileron.

Incorrect aileron travel.

Aileron push rods and
tubes out of rig.

Rig in accordance with aileron
rigging procedures.

Aileron bell crank stops
incorrectly

Rig in accordance with aileron
rigging procedures.

Correct aileron travel
cannot be obtained by
adjusting bellcrank
stops.

Incorrect rigging of push
rods and tubes.

Rig in accordance with aileron
rigging procedures.

Incorrect rigging of
bellcranks.

Rig in accordance with aileron
rigging procedures.

FLAP SYSTEM

Flaps do not extend
(down) or retract (up).

Circuit breaker out.

Reset circuit breaker.

Flaps do not extend
(down) or retract (up).

Defective flap switch.

Replace flap switch.

Defective flap motor.

Replace flap motor.

Defective electrical
circuit.

Replace defective wires.

Stripped or broken
jackscrew on flap motor.

Replace jackscrew assembly.

Содержание S2RHG-T65 TURBO THRUSH

















































































































































































































































































Результаты поиска

Содержание S2RHG-T65 TURBO THRUSH

Отзывы:

Похожие инструкции для S2RHG-T65 TURBO THRUSH

Бренды по названию

Популярные бренды

Thrush Aircraft S2RHG-T65 TURBO THRUSH, Руководство по обслуживанию

Результаты поиска

Содержание S2RHG-T65 TURBO THRUSH

Отзывы:

Похожие инструкции для S2RHG-T65 TURBO THRUSH

Бренды по названию

Популярные бренды