Thermo Scientific Shandon Excelsior ES Скачать руководство пользователя страница 97

Страница: 97 / 131

Shandon Excelsior ES Operator Guide

BE AWARE OF SAMPLES USED. THEY MAY POSE A

BIOHAZARD.

TABLE 1 INSTRUMENT FUNCTION

SYMPTOM

CAUSE

REMEDY

Excelsior ES does

not respond when

the mains power is

switched on.

The instrument is

still carrying out

initial tests.

Wait 30 seconds for the initial

tests to finish.

No power supply

Connect the power lead. Switch

on the mains power and instru-

ment main power switch.

The mains fuses

have blown.

Replace the mains fuse. Replace

the instrument fuses.

Note: Only a technically compe-

tent person should replace fuses.

Excelsior ES is

powered ON, but

the screen is blank.

Instrument in

Standby, screensaver

ON.

Press

on keypad to switch

instrument out of Standby.

The monitor is not

connected correctly.

At the back of the instrument,

ensure that the power and signal

cables are correctly connected.

The monitor is

faulty.

Replace the monitor. Contact

your Thermo dealer.

A process is

started, but the

first reagent is snot

drawn in.

The lid is not

closed.

Open the lid and close by

pressing down firmly on either

side of the knob; do not use the

knob itself to close the lid.

The lid seal is con-

taminated with wax.

Clean the seal lid.

After loading

reagents, a Process

Start screen is not

displayed.

The second short

flush routine at

the end of the load

sequence has not

been run.

Return to the Load Reagents

menu, and complete the se-

quence.

Содержание Shandon Excelsior ES




































































































































Результаты поиска

Содержание Shandon Excelsior ES

Отзывы:

Похожие инструкции для Shandon Excelsior ES

Бренды по названию

Популярные бренды

Thermo Scientific Shandon Excelsior ES, Руководство оператора

Результаты поиска

Содержание Shandon Excelsior ES

Отзывы:

Похожие инструкции для Shandon Excelsior ES

Бренды по названию

Популярные бренды