Thermo Scientific Shandon Excelsior ES Скачать руководство пользователя страница 91

Страница: 91 / 131

Shandon Excelsior ES Operator Guide

Brown wire:

Live (L or L2) terminal

Blue Wire:

Neutral (N or L1) terminal

Green / yellow wire:

Earth terminal - E, ground or V

Insert the appropriate mains cable into the mains connector

on the rear panel of the instrument and clip the cable restraint

over the mains connector. Connect the mains supply cable to

the local power supply outlet.

EXCELSIOR ES MUST BE ELECTRICALLY EARTHED.

MAKE SURE THAT THE INSTRUMENT IS PLUGGED

INTO A PROPERLY EARTHED (GROUNDED) MAINS

SUPPLY.

IT MUST BE POSSIBLE TO INTERRUPT THE MAINS

SUPPLY AT SOURCE BY REMOVING THE PLUG

FROM THE MAINS SUPPLY SOCKET.

Press the I (ON) side of the I / O power switch.

When Excelsior ES is powered ON, you should notice the

following:

1. The cooling fans audibly start, and the instrument LED

lamps illuminate.

2. The rotary valve motor audibly starts.

3. After 30 seconds, the language screen is displayed.

Highlight the required language and select [SELECT]

The screen displays the battery isolation switch and heater

reset alert icons. The icons must be cleared, before any further

operations:

1. Turn ON the battery isolation switch.

Powering

the Instrument ON

Содержание Shandon Excelsior ES




































































































































Результаты поиска

Содержание Shandon Excelsior ES

Отзывы:

Похожие инструкции для Shandon Excelsior ES

Бренды по названию

Популярные бренды

Thermo Scientific Shandon Excelsior ES, Руководство оператора

Результаты поиска

Содержание Shandon Excelsior ES

Отзывы:

Похожие инструкции для Shandon Excelsior ES

Бренды по названию

Популярные бренды