Thermo Scientific Shandon Excelsior ES Скачать руководство пользователя страница 9

Страница: 9 / 131

Shandon Excelsior ES Operator Guide

• Excelsior ES, as supplied, conforms with the international

safety standards, IEC 61010-2-010. However, adding

chemical reagents introduces potential hazards. Good

Laboratory Practice must be followed when dealing with

these chemicals, and operators must consider the potential

for hazard when dealing with particular chemicals.

• BEFORE using reagents, ALWAYS refer to your own

laboratory procedures and manufacturer safety data sheets

(MSDS).

• Many of the reagents used with Excelsior are flammable.

Do not introduce any source of ignition into, or near, the

instrument once it has been loaded with reagents.

Sources of ignition include electrostatic discharge,

resulting from a build-up of static electricity. This can,

under certain conditions, result in ignition of fumes from

any reagent used with Excelsior ES. Good Laboratory

Practice must be followed and ALL necessary precautions

taken.

• Where seismic regulations require the instrument to

be secured, use the handle locations at the rear of the

instrument (2 x M8 female threads). The Centre of

Gravity position for a fully laden instrument is shown in

the diagram:

• Excelsior ES

weighs approximately 112 kilograms (246

lbs) when empty. Do not try to move Excelsior on

your own - at least two people are needed to move an

instrument.

335mm

Centre of Gravity

260mm

Содержание Shandon Excelsior ES




































































































































Результаты поиска

Содержание Shandon Excelsior ES

Отзывы:

Похожие инструкции для Shandon Excelsior ES

Бренды по названию

Популярные бренды

Thermo Scientific Shandon Excelsior ES, Руководство оператора

Результаты поиска

Содержание Shandon Excelsior ES

Отзывы:

Похожие инструкции для Shandon Excelsior ES

Бренды по названию

Популярные бренды