Thermo Scientific Cryofuge 5500i GMP Скачать руководство пользователя страница 65

Страница: 65 / 114

Maintenance and care

Maintenance and care

Maintenance to be performed by the

customer

For the protection of persons, environment and mate-

Cleaning

Pull mains plug before cleaning the

instrument!

rial you are obliged to clean the centrifuge regularly

and to disinfect it if necessary.

Clean the casing, the rotor chamber, the rotor and the

accessories regularly and in case of need. This is

indicated both for reasons of hygiene and to prevent

corrosion due to contamination sticking to the instru-

ment and its accessories.
Clean them with mild agents of pH values ranging

from 6 to 8.
Immediately after cleaning, dry the aluminum parts or

put them into a warm-air dryer at a temperature not

exceeding 50

°C.

Unsuitable cleaning agents or disin-

fection procedures may damage the

centrifuge and its accessories!
If you intend to use cleaning agents

or disinfection procedures not rec-

ommended by the manufacturer,

you have to make sure by consult-

ing the manufacturer, that the pro-

cedure foreseen does not cause any

damages to the instrument!

Содержание Cryofuge 5500i GMP



















































































































Результаты поиска

Содержание Cryofuge 5500i GMP

Отзывы:

Похожие инструкции для Cryofuge 5500i GMP

Бренды по названию

Популярные бренды

Thermo Scientific Cryofuge 5500i GMP, Инструкция по эксплуатации

Результаты поиска

Содержание Cryofuge 5500i GMP

Отзывы:

Похожие инструкции для Cryofuge 5500i GMP

Бренды по названию

Популярные бренды