Thermo Scientific Cryofuge 5500i GMP Скачать руководство пользователя страница 73

Страница: 73 / 114

Troubleshooting

Troubleshooting you can handle yourself

If problems other than those described in the following table arise, you should contact

the authorized customer service.

Error message

Symptoms

Possible causes and corrective measures

Displays remain

dark

The drive stops.
The rotor stops without

deceleration. The lid

cannot be opened.

Mains voltage interrupted

1. Is the mains switch switched on?

2. Check the mains supply.

3. If the mains voltage is OK, contact customer service.

Displays fail

briefly.

The drive stops suddenly.
The rotor stops with de-

celeration.

The display shows E-14.

Brief interruption of mains voltage

1. Turn off mains switch.

2. Check whether the mains plug is connected properly.

3. Restart the centrifuge.

Lid cannot be

opened.

Pressing the “open lid”

key has no effect.

Lid not correctly engaged or lid warped.

1. Check whether mains voltage is on and the instrument is

switched on (display is lit).

2. Press lid down in the center of the front section once, and ac-

tuate the “open lid” key subsequently.

3. If this is unsuccessful, you may open the lid using the me-

chanical emergency lid release (see page 67)

Содержание Cryofuge 5500i GMP



















































































































Результаты поиска

Содержание Cryofuge 5500i GMP

Отзывы:

Похожие инструкции для Cryofuge 5500i GMP

Бренды по названию

Популярные бренды

Thermo Scientific Cryofuge 5500i GMP, Инструкция по эксплуатации

Результаты поиска

Содержание Cryofuge 5500i GMP

Отзывы:

Похожие инструкции для Cryofuge 5500i GMP

Бренды по названию

Популярные бренды