Thermo Scientific Cryofuge 5500i GMP Скачать руководство пользователя страница 34

Страница: 34 / 114

Rotors and accessories

BIOshield

- Rotor

The bucket set is a permanent part of the rotor and

must not be interchanged with other rotors.
Do not run the rotor without the rotor lid closed. The

rotor lid is opened respectively closed by pushing

down and turning the lid locking knob at the same

time.

Store the BIOshield

Rotor with the lid

removed after cleaning. This will enable

the rotor to dry completely.

Exceeding the maximum number of

cycles can result in rotor fracture

leading to a destruction of the cen-

trifuge!

max. cycles

22000

31000

max. speed

5850 rpm

5350 rpm

The rotor has to be replaced upon

reaching the end of its service life

depending on the mechanical load

and on the speed respectively.

Содержание Cryofuge 5500i GMP



















































































































Результаты поиска

Содержание Cryofuge 5500i GMP

Отзывы:

Похожие инструкции для Cryofuge 5500i GMP

Бренды по названию

Популярные бренды

Thermo Scientific Cryofuge 5500i GMP, Инструкция по эксплуатации

Результаты поиска

Содержание Cryofuge 5500i GMP

Отзывы:

Похожие инструкции для Cryofuge 5500i GMP

Бренды по названию

Популярные бренды