Thermo Scientific Cryofuge 5500i GMP Скачать руководство пользователя страница 46

Страница: 46 / 114

Operation

Improper or improperly combined

accessories may cause severe

damage to the centrifuge!

Installing the rotor

The rotors approved for the

Cryofuge

5500i GMP

are

detailed in the chapter “Rotors and Accessories” on

page 17. Use only rotors listed.
To install the rotor

you need the socket wrench sup-

plied (see chapter “Schedule of parts” on page 8).

Proceed as follows:
1. Open the lid and make sure that rotor chamber

and rotor are clean. Remove any dust, foreign ma-

terial or sample residues out of chamber before

use.

2. Check whether the collet chuck is loose (collet

chuck moves freely on the spindle). If not, loosen

the rotor seat using the socket wrench supplied.

3. Place the rotor on the drive shaft so that the rotor

chuck is located precisely above the center.

4. The rotor must glide freely down the collet chuck

until it hits the lower stop.

5. If you have installed the rotor correctly, you can

tighten the collet chuck easily using the socket

wrench supplied.

6. Place the rotor lid on the rotor and screw it tightly.

Regularly check the correct positioning

of the rotor and re-tighten the collet

chuck as needed.

Содержание Cryofuge 5500i GMP



















































































































Результаты поиска

Содержание Cryofuge 5500i GMP

Отзывы:

Похожие инструкции для Cryofuge 5500i GMP

Бренды по названию

Популярные бренды

Thermo Scientific Cryofuge 5500i GMP, Инструкция по эксплуатации

Результаты поиска

Содержание Cryofuge 5500i GMP

Отзывы:

Похожие инструкции для Cryofuge 5500i GMP

Бренды по названию

Популярные бренды