Thermo Scientific A55867 Скачать руководство пользователя страница 188 | Manualshive

Страница: 188 / 198

background image

Instrument component and accessory disposal

To minimize negative environmental impact from disposal of electronic waste, do not dispose of
electronic waste in unsorted municipal waste. Follow local municipal waste ordinances for proper
disposal provision and contact customer service for information about responsible disposal options.

Environmental requirements

WARNING!

The emissions characteristics of this equipment make it suitable for use in industrial

areas and hospitals (CISPR 22 class A). If it is used in a residential environment (for which CISPR
11 class B is normally required) this equipment may not offer adequate protection to radio-frequency
communication services. It may be necessary for the user to take mitigation measures, such as
relocating or re-orienting the equipment.

Condition

Acceptable range

Installation site

Indoor use only

Electromagnetic interference

Do not use this instrument in close proximity to
sources of strong electromagnetic radiation (for
example, unshielded intentional RF sources). Strong
electromagnetic radiation may interfere with the
proper operation of the instrument.

Pollution degree

The instrument has a Pollution Degree rating of
II. The instrument may only be installed in an
environment that has non-conductive pollutants
such as dust particles or wood chips. Typical
environments with a Pollution Degree II rating are
laboratories and sales and commercial areas.

Electromagnetic compatibility (EMC) standards

Class A notice

This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules; and CISPR 11 Class A. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area or domestic environment is likely to
cause harmful interference in which case the user will be required to correct the interference at his own
expense. Do not use this device in close proximity to sources of strong electromagnetic radiation (e.g.
unshielded intentional RF sources), as these can interfere with the proper operation.

Appendix E

Safety

Environmental requirements

E

188

CTS

™

DynaCellect

™

Magnetic Separation System User Guide

«
...
186
187
188
189
190
...
»

Содержание A55867







































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для A55867

Бренд: NORLUX Страницы: 2

Бренд: Nektar Страницы: 3

Бренд: Youkey Страницы: 86

Martin ERA 800 Performance

Бренд: Harman Страницы: 32

Martin ERA 600 Performance

Бренд: Harman Страницы: 32

Бренд: Sabre Страницы: 2

Бренд: Pahlen Страницы: 20

Бренд: Paia Страницы: 7

Бренд: Gardena Страницы: 33

Бренд: A.HABERKORN Страницы: 28

Бренд: Crosley Страницы: 6

Бренд: Gambro Страницы: 273

SpinVessel VP 418SV3-1-850RB-CC

Бренд: V&P Scientific Страницы: 9

MACDON C HARVESTEC 6000

Бренд: CORN Страницы: 24

Бренд: Star Страницы: 16

AtLite Sure-Lites SELDWA29SD

Бренд: Eaton Страницы: 4

Бренд: Xils lab Страницы: 31

Бренд: Car Solutions Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды