Главная
/
Thermo Scientific
/
A55867
/
Руководство пользователя

Thermo Scientific A55867, Руководство пользователя

Поделиться

Страница: 183 / 198

background image

Safety compliance

The instrument design and manufacture complies with the following standards and requirements for
safety, electromagnetic compatibility, and Environmental WEEE.

Reference

Description

EU Directive 2014/35/EU

European Union “Low Voltage Directive”

IEC 61010-1

EN 61010-1

UL 61010-1

CAN/CSA C22.2 No. 61010-1

Safety requirements for electrical equipment for
measurement, control, and laboratory use – Part 1:
General requirements

IEC 61010-2-081

EN 61010-2-081

Safety requirements for electrical equipment for
measurement, control and laboratory use – Part
2-081: Particular requirements for automatic and
semi-automatic laboratory equipment for analysis
and other purposes

Informational symbols

Symbol and description

CAUTION!

Risk of danger. Consult the manual for further safety information.

CAUTION!

Risk of electrical shock.

WEEE (Waste Electrical and Electronic Equipment) symbol indicates that this product
should not be disposed of in unsorted municipal waste. Follow local municipal waste
ordinances for proper disposal provisions to reduce the environmental impact of WEEE.

This instrument meets European requirement WEEE Directive 2012/19/EU.

ON

(power)

OFF

(power)

Protective earth (ground)

The CE mark symbolizes that the product conforms to all applicable European
Community provisions for which this marking is required. Operation of the CTS

™

Xenon

™

Electroporation Instrument is subject to the conditions described in this manual. The
protection provided by the device may be impaired if the instrument is used in a manner not
specified by the manufacturer.

Appendix E

Safety

Symbols on this instrument

E

CTS

™

DynaCellect

™

Magnetic Separation System User Guide

183

«
...
181
182
183
184
185
...
»

Содержание A55867







































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для A55867

Бренд: OMCA Страницы: 72

Бренд: Barko Hydraulics Страницы: 92

Бренд: Taurus Страницы: 28

Бренд: Kärcher Страницы: 54

Бренд: ABB Страницы: 85

Бренд: Labnet Страницы: 5

Бренд: idiag Страницы: 12

Бренд: Mandam Страницы: 9

Бренд: Radial Engineering Страницы: 2

Бренд: Radial Engineering Страницы: 2

Бренд: M-system Страницы: 4

Бренд: American DJ Страницы: 8

Бренд: COURANT Страницы: 2

Бренд: laerdal Страницы: 64

BRUTE AFS570010

Бренд: KStrong Страницы: 8

Бренд: YOKOGAWA Страницы: 2

Бренд: SafeWaze Страницы: 2

Бренд: RAMVAC Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды