Thermo Scientific 1300 Series Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 130

background image

1300 Series A2 4-3

Thermo Scientific

Section 4

Operation

The following are the operating modes for this unit.

• OFF mode

• Window open mode

• Working mode

• Standby mode

• UV mode

Off mode

means the unit is in an idle state. The unit is turned off

(blowers are off). The sample chamber light is enabled. The unit is
connected to a power source. The power supply for the internal outlets is
enabled when the blue LED “internal power supply on” is lighted.

Window open mode

is the state in which the window is open and

positioned outside of the 250mm working position. To install or remove
accessories, the front window can be moved to the maximum open
position. For cleaning, the front window can be lowered beyond the closed
position (see Use of the Window, Section 1).

The air system blowers are switched on with the red LED “airflow not
steady” lighted. The front window is not in the work position, with the
red LED “front window not in work position” is lighted. The sample
chamber light is enabled. The power supply for the internal outlets is
enabled with the blue LED “internal power supply on” is lighted.

Working mode

is active when the front window is in the working position

(250 mm opening) and the air system is operating steadily. The green
LEDs “front window is in work position” and “airflow steady” are lighted.

The markings on the side guide rails and the lower edge of the front
window are at the same height with no audible alarm signal.

The sample chamber light and power for the internal outlets are enabled
with the yellow LED “internal power supply activated” is lighted.

The RS-232 contact is open. The display shows operating hours,
downflow velocity and exhaust air velocity.

Standby mode

is the state in which the window is closed with the blower

velocity reduced. The red LED “front window not in work position” and
the blue LED “airflow reduced” are lighted.

The sample chamber illumination is enabled. The internal power supply in
the sample chamber is enabled. The red LED “airflow not steady” and the
blue LED “internal power supply activated” are lighted.

Operating Modes

«
...
32
33
34
35
36
...
»

Содержание 1300 Series



































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1300 Series

Бренд: YYZ Lighting Страницы: 3

Бренд: Camp Safety Страницы: 118

Бренд: Ultrafast Systems Страницы: 39

Бренд: Mackworth Страницы: 2

Бренд: CAMPAGNOLA Страницы: 209

Бренд: Jackco Страницы: 6

Бренд: Teac Страницы: 44

Бренд: Te Pari Страницы: 6

Бренд: Hach Страницы: 456

Бренд: Baileigh Industrial Страницы: 12

Бренд: Zodiac Страницы: 2

Бренд: Zipper Mowers Страницы: 37

Бренд: Zimmer Страницы: 46

LUNAQUA Classic LED

Бренд: Oase Страницы: 16

Бренд: Feniex Страницы: 5

Бренд: Parkside Страницы: 88

DSO8000E Series

Бренд: Hantek Страницы: 95

Бренд: Marcy Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды