Thermo Scientific 1300 Series Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 130

background image

Thermo Scientific

1300 Series A2

iii

Preface

Important operating and/or maintenance instructions. Read the accompanying text carefully.

Potential electrical hazards. Only qualified persons should perform procedures associated with this
symbol.

Equipment being maintained or serviced must be turned off and locked off to prevent possible injury.

Hot surface(s) present which may cause burns to unprotected skin, or to materials which may be
damaged by elevated temperatures.

The agents used and/or work performed in this cabinet may be hazardous to your health and the
health of others. (The cabinet must be used properly. You must read the operators manual before
using.)

Marking of electrical and electronic equipment, which applies to electrical and electronic equipment
falling under the Directive 2012/19/EU (WEEE) and the equipment that has been put on the market
after 13 August 2005.

This product is required to comply with the European Union’s Waste Electrical & Electronic
Equipment (WEEE) Directive 2012/19/EU. It is marked with the WEEE symbol. Thermo Fisher
Scientific has contracted with one or more recycling/disposal companies in each EU Member State
European Country, and this product should be disposed of or recycled through them. Further
information on Thermo’s compliance with this directive, the recyclers in your country and
information on Thermo Scientific products will be available at www.thermofisher.com.

4

Always use the proper protective equipment (clothing, gloves, goggles, etc.)

4

Always dissipate extreme cold or heat and wear protective clothing.

4

Always follow good hygiene practices.

4

Each individual is responsible for his or her own safety.

General Notes

Safety

«
...
2
3
4
5
6
...
»

Содержание 1300 Series



































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1300 Series

Бренд: CAIRE Страницы: 2

Бренд: EarthQuake Страницы: 28

Бренд: TAIKO Audio Страницы: 24

Бренд: Ace Страницы: 17

Бренд: ACE INSTRUMENTS Страницы: 33

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: ACE INSTRUMENTS Страницы: 2

Бренд: TapFlo Страницы: 35

Бренд: DANA Страницы: 8

Бренд: 2E Страницы: 6

Бренд: Garmin Страницы: 2

Бренд: H&S Страницы: 32

MIAMI J ADVANCED

Бренд: Össur Страницы: 35

Бренд: Össur Страницы: 38

Бренд: Össur Страницы: 8

Бренд: Össur Страницы: 72

Бренд: Össur Страницы: 76

Miami Lumbar Posteo

Бренд: Össur Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды