Thermo Scientific 1300 Series Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 130

background image

Description:

• Determines the integrity of the downflow and exhaust filters.

Equipment:

• Aerosol Photometer, or equivalent

• Aerosol Generator, or equivalent

Method:

1. Allow the cabinet to operate for approximately 20 minutes.

2. Remove the work tray and protective covers, as appropriate.

3. Introduce the aerosol from the generator in the center rear of the work

area, using a tee fitting to evenly distribute the aerosol.

4. If desired, and if the cabinet has not been used with hazardous

materials since an effective decontamination, the upstream
concentration can be measured. If desired, connect the photometer
sample hose to the appropriate (supply or exhaust) test hose
connection (exhaust test hose - right side / supply test hose - left side)
from under the work tray.

5. Using either the appropriate upstream challenge measurement or

calculated challenge value, set the photometer accordingly.

6. Scan the downstream side and perimeter of the filter as prescribed in

YY 0569-2005.

Acceptance:

• Filters scanned – 0.01% of upstream concentration at any point

Method:

1. Set up as in Steps 1 through 5 above

2. In the duct, downstream of the filter, sample in accordance with YY

0569-2005.

Acceptance:

• Filters not scanned – 0.005% of upstream concentration

1300 Series A2

8-11

Thermo Scientific

Section 8

Certification Testing

HEPA Filter Leak Test

Filters that can be

Accessed and Scanned

Filters that cannot be

Accessed or Scanned

«
...
62
63
64
65
66
...
»

Содержание 1300 Series



































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1300 Series

Бренд: UnionSpecial Страницы: 56

Бренд: MAHLE Страницы: 21

Бренд: JB-Lighting Страницы: 60

Бренд: Baker Страницы: 82

Бренд: Tascam Страницы: 128

Бренд: ParaBody Страницы: 6

Бренд: Faderfox Страницы: 8

Бренд: Pablo Страницы: 7

Бренд: Ultraflex Страницы: 3

Бренд: Mackie Страницы: 18

Бренд: Mackie Страницы: 2

Бренд: Mackie Страницы: 8

Бренд: Mackie Страницы: 7

Бренд: ParaBody Страницы: 6

Бренд: ParaBody Страницы: 11

Бренд: Vahle Страницы: 36

Бренд: Vahle Страницы: 20

Бренд: Vacon Страницы: 102

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды