Thermo Scientific 1300 Series Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 130

background image

•

Testing

Tests include factory final test, type test, field test and maintenance
test according to YY 0569-2005.

•

Factory Final Tests

The testing would be conducted before delivery in accordance with the
clauses 5.1, 5.2, 5.3, 5.4.1~5.4.5, 5.4.7~5.4.15 on YY0569-2005

•

Type Tests

According to clause 7.3 of YY0569-2005, Type test shall be randomly
sampled from cabinets for delivery. Samples for type test shall be
provided by the manufacturer, and the test must be performed by
qualified certification bodies.

The testing would be conducted in accordance with the clauses 5.1,
5.2, 5.3, 5.4 on YY0569-2005

•

Field Tests

Field testing would be performed after installation and cabinet
re-location. The testing would be conducted in accordance with the
clauses 5.1, 5.4.2, 5.4.7~5.4.9, 5.4.14 on YY 0569-2005

•

Maintenance Tests

The testing would be conducted in accordance with the clauses 5.1,
5.4.2, 5.4.7~5.4.9, 5.4.14 on YY 0569-2005 at least once a year. Test
also would be performed after filters are changed and interior parts are
repaired.

1300 Series A2

8-3

Thermo Scientific

Section 8

Certification Testing

Testing (continued)

«
...
54
55
56
57
58
...
»

Содержание 1300 Series



































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1300 Series

Бренд: Varec Страницы: 74

Бренд: Halyard Страницы: 84

Бренд: PAIDI Страницы: 48

Бренд: MacDon Страницы: 89

Бренд: Yates Страницы: 2

Бренд: Raven Страницы: 27

Бренд: Raven Страницы: 79

Бренд: Raven Страницы: 88

Бренд: Ecco Страницы: 9

Бренд: Talet Equipment Страницы: 17

Бренд: EASTERN INSTRUMENTS Страницы: 93

Бренд: EarthQuake Страницы: 12

Бренд: Pari Страницы: 2

Бренд: IDS Страницы: 2

Бренд: IFM Страницы: 175

Бренд: IFM Страницы: 5

Бренд: Land Pride Страницы: 38

Бренд: LANGER EMV-Technik Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды