THERMEx THW100 Скачать руководство пользователя страница 49

Страница: 49 / 58

Heat Pump Manual

COMMISSIONING

Water Connection

Was the pressure on the suction
gauge checked before the unit
was filled with water

– see

Installation

Open the mains make up water
to the heat pump

– has all the

air been bled from the system

Check the water path for leaks

Start Up

Press the ON/OFF button on the front of the heat pump and the pump will start up

After adding power to the heat
pump, change the water
temperature setting and all other
alarms to customer or site needs

After heat pump has started
check and note down the current
draw for the compressors, pump
and fans
Pump < 6 amps
Compressors < 28 amps
Fans < 8 amps

Note down the water flow
reading
Should be ~ 2 l/s

Note down pump pressure

Does pump performance fall on
the respective pump curve

Check the sight glass for
evidence of bubbles or moisture

Check that water temperature is
dropping

Note down the oil level on the
compressor sight glass

Adjust the bypass valve to suit
customer and/ or site needs

Fit gauges and note down
running pressures on the heat
pump

Содержание THW100



























































Результаты поиска

Содержание THW100

Отзывы:

Похожие инструкции для THW100

Бренды по названию

Популярные бренды

THERMEx THW100, Руководство по эксплуатации продукта

Результаты поиска

Содержание THW100

Отзывы:

Похожие инструкции для THW100

Бренды по названию

Популярные бренды