THERMEx THW100 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 58

background image

Heat Pump Manual

30

OPERATION

Using the key pad controller

All the setting can be viewed and all the operational parameters can be set from the
controller inside the electrical box using the key pad on the front of the controller.

There are four buttons

– ▲▼ X and OK – they scroll up and down through the menu items

and the OK button is used for selecting the item. Pressing the escape button

– X – will revert

back to the home screen.

Operational parameters that are displayed on the front page of the controller are listed under
these menus

VIEW INFO

– Under this menu is

-

IP address of the machine

-

Current time

-

Total CH/HT pumps

– this will give the number of slave heat pumps the system can

detect is installed

-

Software version

VIEW TEMPS

-

HTW supply

– this is the hot water temperature going through the machine

-

HT TANK TEMP

– this is the temperature of the water in the storage tank and the

master controller temperature

-

CCT1 DISCHARGE TEMP

– circuit 1 discharge temperature – on a two compressor

unit discharge temperatures and not pressures are monitored

-

CCT2 DISCHARGE TEMP

– circuit 2 discharge temperature

VIEW PRESSURES

-

CCT 1 SUCTION PRESSURE

– circuit 1 suction pressure

-

CCT2 SUCTION PRESSURE

– circuit 2 suction pressure – on a heat pump with 1

compressor the discharge pressure will show here also

VIEW ON TIMES

-

This will give the run times on the compressor

VIEW HT LOAD

-

If the unit is supplied with a flow meter

– typically on units designed to operate above

60C

– then the software will be doing heat load calculations.

-

Any faults are indicated on the face of the control panel.

It  is  a  good  idea  after  the  unit  has  been  running  for  5  minutes  check  that  the  water
temperature is rising  and check there are no bubbles in the sight glass

– if these two things

are happening then the unit is running properly. Give the system a final check to ensure that
there are no water leaks.  An amp meter can also be run over the wires into the contactors to
ensure that the compressor and the pump are drawing the right amount of amps according to
the technical data.

Replace the front panel and the display on the front of the unit will show storage or heat pump
water temperature.

Once the unit has been connected to the internet using the procedure outlined above then the
webpage can be monitored.

«
...
28
29
30
31
32
...
»

Содержание THW100



























































Отзывы:

Нет отзывов

Похожие инструкции для THW100

Бренд: TapFlo Страницы: 31

Бренд: JABSCO Страницы: 32

Evosta2 11/139 SAN V

Бренд: DAB Страницы: 31

Бренд: DAB Страницы: 19

Бренд: EBARA Страницы: 22

Бренд: VARISCO Страницы: 72

Бренд: Zehnder Rittling Страницы: 4

Бренд: Amana Страницы: 26

Comfortstat 2 F 8ST

Бренд: GDC Страницы: 28

Бренд: nedis Страницы: 60

Бренд: iGenix Страницы: 9

GUARDIAN Smart Sense AD250

Бренд: L.B. White Страницы: 24

Бренд: MILL Страницы: 10

Бренд: Xylem Страницы: 56

Бренд: Grundfos Страницы: 16

1542A-SP Series

Бренд: Hypro Страницы: 8

Бренд: Vornado Страницы: 9

Бренд: OilGear Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды