THERMEx THW100 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 58

background image

Heat Pump Manual

34

CONTROL

To  protect  the  system  the  evaporator  the  water  to  water  units  will  be  supplied  with  a  flow
meter so if the flow drops then it will shut the unit down until the flow returns.

There  is  also  an  evaporator  water  temperature  sensor  and  if  the  temperature  drops  below
this set point it will shut the unit down until the water temperature increases.

The water to water units still have a flow switch in the condenser water line so if this trip it will
interrupt  the  flow  control  of  the  evaporator  water.  A  generic  flow  alarm  will  be  raised.
Investigation  will  be  needed  to  check  whether  the  fault  is  condenser  water  or  evaporator
water. The data logs will help with this.

SERVICE and MAINTENANCE

Warning: Always isolate the power from the heat pump prior to working on the unit.

Warning: Always ensure that personnel have read and understood the SAFETY section of
this manual prior to working on the heat pump.

Warning: When the mains controller is de-energised the power contactors are live, even if the

components are not operating.

All maintenance must be carried out by qualified refrigeration mechanics.

These  units  have  been  designed  for  the  minimum  of  maintenance.  However  to  ensure
optimum  performance  qualified  personnel  should  carry  out  regular  maintenance.  A
comprehensive preventative maintenance program is available through Thermex carried out
by qualified refrigeration mechanics.

Should any faults be identified then please call Thermex to arrange a service call.

Recommended preventative maintenance program

Operation

Frequency

Refrigerant Charge

6 Monthly

Electrical connections are tight

6 Monthly

Compressor amp draw

12 Monthly

Pump amp draw

12 Monthly

Condenser strainer cleaned

6 Monthly

Cables - inspect all cables to check no damage from hot spots or sharp
points

Every visit

Accessing the electrical box – standard heat pump

There will be two M6 bolts on the front of the unit. Unscrew these to gain access to the
electrical switching gear. Always remember that there are parts in the electrical enclosure
that are operating at line voltage only qualified technicians should access the electrical box.

«
...
32
33
34
35
36
...
»

Содержание THW100



























































Отзывы:

Нет отзывов

Похожие инструкции для THW100

Бренд: wallas Страницы: 43

Бренд: Vallox Страницы: 20

Бренд: Valeo Страницы: 88

Бренд: Valdemar Energy Страницы: 61

Aquarea WH-ADC0309J3E5B

Бренд: Panasonic Страницы: 40

Бренд: Calpeda Страницы: 43

Бренд: Argo Страницы: 10

UFLEX SilverSteer UP25 F-SVS

Бренд: Ultraflex Страницы: 29

Бренд: ICP Страницы: 14

Бренд: Xylem Страницы: 56

Бренд: Grundfos Страницы: 16

1542A-SP Series

Бренд: Hypro Страницы: 8

Бренд: Zibro Страницы: 75

Бренд: DAB Страницы: 292

Бренд: S&P Страницы: 20

Бренд: Atlantic Страницы: 24

Бренд: ElectrIQ Страницы: 23

Бренд: Hozelock Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды