en-67
OPERATION 7
7.12 MOWING ON SLOPES _________________________________________________
The mower has been designed for good traction and
stability under normal mowing conditions. Use caution
when operating on slopes, especially when the grass
is wet. Wet grass reduces traction and steering
control.
1.
Always mow with the engine at full throttle,
control forward speed using traction foot
pedal to maintain proper cutting.
2.
Use weight transfer control as required to
improve weight distribution between decks
and mower.
3.
If the mower tends to slide or the tyres begin
to mark the turf, angle mower into a less
steep slope until traction is regained or tyre
marking stops.
4.
If mower continues to slide or mark the turf,
the slope is too steep for safe operation. Do
not make another attempt to climb, and back
down slowly.
5.
When descending a steep slope, always
lower implements to the ground to reduce the
risk of mower overturning.
Correct tyre pressure is essential for maximum
traction.
See Specification
WARNING
To Minimize The Possibility Of Overturning,
The Safest Method For Operating On Hills
And Terraces Is To Travel Up And Down The
Face Of The Slope (Vertically), Not Across
The Face (Horizontally). Avoid Unnecessary
Turns, Travel At Reduced Speeds, And Stay
Alert For Hidden Hazards.
To Ensure best Stability Always Load The Left
Hand Storage Rack First And Cut With All
Three Units Powered.
A
0°
0%
2-3/4°
5%
5-3/4°
10%
8-1/2°
15%
11-1/4°
20%
14°
25%
16-3/4°
30%
19-1/4°
35%
21-3/4°
40%
24-1/4°
45%
26-1/2°
50%
28-
3/4°
55%
31°
60
%
33°
65
%
35°
70%
36-3/4°
75%
38-3/4°
80%
40-1/4°
85%
42°
90%
43-1/2°
95%
45°
100%
Deg
rees
Gr
ade
A
A = Maximum Allowable Slope
A = Maximum Allowable Slope
Degrees are shown to the nearest 1/4”.
General slope of roadway embankment - 45°
Steepest grass area - 31°
Slope of average roof - 19-1/4°
2nd class highway maximum grade 4-1/2°
Toll road or freeway - 1-3/4°
Содержание Jacobsen Ransomes Parkway 3 Meteor LGNN344
