en-60
7 OPERATION
7.3
OPERATING PROCEDURE ______________________________________________
1.
Under no circumstances must the engine be started without the operator seated on the tractor.
2.
Do not operate tractor or attachments with loose, damaged or missing components. Whenever possible
mow when grass is dry
3.
First mow in a test area to become thoroughly familiar with the operation of the tractor and controls.
4.
Study the area to determine the best and safest operating procedure. Consider the height of the grass,
type of terrain, and condition of the surface. Each condition will require certain adjustments or
precautions.
5.
Do Not direct discharge of material toward bystanders, nor allow anyone near the machine while in
operation. The owner/operator is responsible for injuries inflicted to bystanders and/or damage to their
property.
6.
Use discretion when mowing near gravel areas (roadway, parking areas, cart paths, etc.). Stones
discharged from the implement may cause serious injuries to bystanders and/or damage the
equipment.
7.
Disengage the cutter motors and raise the implements when crossing paths or roads. Look out for
traffic.
8.
Stop and inspect the equipment for damage immediately after striking an obstruction or if the machine
begins to vibrate abnormally. Have the equipment repaired before resuming operation.
CAUTION
To Help Prevent Injury, Always Wear Safety Glasses, Leather Work Shoes Or Boots, A
Hard Hat And Ear Protection.
WARNING
Ensure protective skirts are in position and in good condition.
CAUTION
Remove All Debris From The Site Before Mowing. Enter A New Area Cautiously Always
Operate At Speeds That Allow You To Have Complete Control Of The Mower.
CAUTION
Before You Clean, Adjust, Or Repair This Equipment, Always Disengage All Drives, Lower
Implements To The Ground, Engage Parking Brake, Stop Engine And Remove Key From
Ignition Switch To Prevent Injuries.
Содержание Jacobsen Ransomes Parkway 3 Meteor LGNN344
