Terex Genie Z-40 Скачать руководство пользователя

Страница: 99 / 287

June 2022

Service and Repair Manual

Track Components

Part No. 1268555GT

-62/40

14 Using the pry bars, lift the sprocket half into

position. Install the 2 sprocket retaining

fasteners and torque to specification. Refer to

Specifications,

TraX Torque Specifications

15 Attach a lifting strap from an overhead

supporting device to the center-point of the

track assembly, above the sprocket.

16 Install the track assembly onto the drive hub

adapter while guiding the hub adapter studs

into the sprocket of the track assembly. Install

as many sprocket retaining fasteners as

possible to the hub adapter and torque to

specification. Refer to Specifications,

TraX

Torque Specifications

Crushing hazard. The track

assembly could become

unbalanced and fall when

installed onto the machine if not

properly supported by the

overhead crane.

17 Adjust the track tension. Locate the grease

plug on the track tension cylinder. Loosen the

plug, but do not remove it.

18 Locate the grease zerk fitting on the other

side of the track tension cylinder.

1 grease zerk
2 grease plug

19 Pump grease into the grease zerk fitting until

grease, free from air, comes out of the grease

plug. Securely tighten the grease plug. Do not

over tighten.

20 Continue to pump grease into the grease

fitting just until the idler wheel moves. Check

the track tension.

Result: There should be less than 1 inch /

2.5 cm of gap between the bogey wheels and

the inside surface of the track. Proceed to

step 22.

Result: There is 1 inch / 2.5 cm or more of

gap between the bogey wheels and the inside

surface of the track. Proceed to step 21.

1 bogey wheels

Содержание Genie Z-40
































































































































































































































































































Результаты поиска

Содержание Genie Z-40

Отзывы:

Похожие инструкции для Genie Z-40

Бренды по названию

Популярные бренды

Terex Genie Z-40, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание Genie Z-40

Отзывы:

Похожие инструкции для Genie Z-40

Бренды по названию

Популярные бренды