Terex Genie Z-40 Скачать руководство пользователя

Страница: 94 / 287

Service and Repair Manual

June 2022

Turntable Rotation Components

-62/40

Part No. 1268555GT

Turnta ble R ota tion C ompone nt s

9-1 Tur nta ble Rot ation Assem bly

9-1

Turntable Rotation Assembly

How to Remove the Turntable

Rotation Assembly

Note: When removing a hose assembly or fitting,

the O-ring (if equipped) on the fitting and/or hose

end must be replaced. All connections must be

torqued to specification during installation. Refer to

Specifications,

Hydraulic Hose and Fitting Torque

Specifications.

Note: Perform this procedure with the machine on

a firm, level surface.
1 Start the machine and rotate the boom 90° to

either side of the drive chassis.

2 Loosen the retaining fasteners securing the

turntable rotation gear backlash plate.

Note: Do not loosen the jam nut securing the

backlash adjustment bolt.

1  jam nut
2  adjustment bolt
3  pivot plate retaining fasteners

3 Start the machine and rotate the boom back

to the stowed position.

4 Secure the turntable from rotating with the

turntable rotation lock.

Tip-over hazard. The machine

could tip over when the turntable

rotation assembly is removed if

the turntable rotation lock is not

in the locked position.

5 Raise the secondary boom until the upper

pivot is 6 feet / 2 m above the counterweight.

6 Install a cylinder chock (Genie part number

33484) onto the secondary lift cylinder rod.

Lower the secondary just until the chock

makes contact with the barrel of the lift

cylinder.

Note: Do not apply all the weight of the secondary

boom on the chock.
7 Loosen the jam nut securing the backlash

adjustment bolt. Turn the adjustment bolt

counter-clockwise until the turntable rotation

assembly can move freely.

8 Tag, disconnect and plug the hydraulic hoses

from the turntable rotation motor manifold.

Cap the fittings on the manifold.

Bodily injury hazard. Spraying

hydraulic oil can penetrate and

burn skin. Loosen hydraulic

connections very slowly to allow

the oil pressure to dissipate

gradually. Do not allow oil to

squirt or spray.

9 Remove the turntable rotation assembly

mounting fasteners.

Содержание Genie Z-40
































































































































































































































































































Результаты поиска

Содержание Genie Z-40

Отзывы:

Похожие инструкции для Genie Z-40

Бренды по названию

Популярные бренды

Terex Genie Z-40, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание Genie Z-40

Отзывы:

Похожие инструкции для Genie Z-40

Бренды по названию

Популярные бренды