Terex Genie Z-40 Скачать руководство пользователя

Страница: 44 / 287

Service and Repair Manual

June 2022

Platform Components

-62/40

Part No. 1268555GT

5 Open the bottom bleed screw on the rotator,

but do not remove it.

Bodily injury hazard. Spraying

hydraulic oil can penetrate and

burn skin. Loosen hydraulic

connections very slowly to allow

the oil pressure to dissipate

gradually. Do not allow oil to

squirt or spray.

6 Move the function enable toggle switch to

either side and hold the platform rotate toggle

switch to the right position until the platform is

fully rotated to the right. Continue holding the

toggle switch until air stops coming out of the

bleed screw. Close the bleed screw.

Crushing hazard. Keep clear of

the platform during rotation.

7 Clean up any hydraulic oil that may have

spilled.

8 Rotate the platform fully in both directions and

inspect the bleed screws for leaks.

2-3 Plat for m Ove rloa d Syste m

2-3

Platform Overload System

(if equipped)

How to Calibrate the Platform

Overload System

Calibrating the platform overload system regularly

is essential to safe machine operation. Continued

use of an improperly operating platform overload

system, could result in the system not sensing an

overloaded platform condition. Machine stability

could be compromised resulting in the machine

tipping over.Note: Perform this procedure with the

machine on a firm, level surface.
1 Turn the key switch to platform control. Start

the engine and level the platform.

2 Determine the maximum platform capacity.

Refer to the machine serial plate.

3 Remove all weight, tools and accessories

from the platform.

Note: Failure to remove all weight, tools and

accessories from the platform will result in an

incorrect calibration.
4 Using a suitable lifting device, place a test

weight equal to the maximum platform

capacity at the center of the platform floor.

Refer to the machine serial plate.

Содержание Genie Z-40
































































































































































































































































































Результаты поиска

Содержание Genie Z-40

Отзывы:

Похожие инструкции для Genie Z-40

Бренды по названию

Популярные бренды

Terex Genie Z-40, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание Genie Z-40

Отзывы:

Похожие инструкции для Genie Z-40

Бренды по названию

Популярные бренды