Terex Genie Z-40 Скачать руководство пользователя

Страница: 37 / 287

June 2022

Service and Repair Manual

Platform Controls

Part No. 1268555GT

-62/40

10 Slowly move the joystick off center in either

direction just until the function begins to

move.

11 Slowly move the joystick back towards the

neutral position. Just before the function stops

moving, move the drive enable toggle switch

to either side to set the threshold.

Result: The alarm should sound indicating a

successful calibration.

Note: For each joystick axis, the threshold must be

set for both directions.
12 Repeat steps 9 through 11 for each direction

of boom joystick controlled machine function

(boom up/down, boom extend/retract and

turntable rotate left/right).

13 Return the joystick to the neutral position and

wait for approximately 10 seconds to allow the

settings to be saved.

Result: The alarm should sound indicating

that the settings have been saved in memory.

Note: Do not operate any machine function during

the 10 second waiting time.

How to Adju st th e Joys tick M ax-o ut Setti ng

How to Adjust the Joystick Max-

out Setting

The max-out setting of a joystick controls the

maximum speed of a joystick-controlled machine

function. Whenever a hydraulic cylinder, drive

motor or hydraulic pump is replaced, the max-out

setting should be adjusted to maintain optimum

performance. The max-out settings on the joystick

can be changed to compensate for hydraulic pump

wear to maintain peak performance from the

machine.
Note: Perform this procedure with the boom in the

stowed position.
1 Pull out the red Emergency Stop button to the

on position at both the ground and platform

controls.

2 Turn the key switch to platform control. Do not

start the engine.

3 Push in the platform controls red Emergency

Stop button to the off position.

4 Do not press down the foot switch.
5 Move and hold the drive enable toggle switch

in the right position and pull out the red

Emergency Stop button to the on position.

6 When the alarm sounds, release the drive

enable toggle switch.

7 Momentarily activate the drive enable toggle

switch in the right direction 4 times.

Result: There should be a pause and the

alarm should sound 4 times indicating that the

machine is in max-out calibration mode.

8 Start the engine from the platform controls

and press down the foot switch.

9 Start a timer and activate the machine

function that needs to be adjusted. Record the

time it takes for that function to complete a full

cycle (ie; boom up).

Содержание Genie Z-40
































































































































































































































































































Результаты поиска

Содержание Genie Z-40

Отзывы:

Похожие инструкции для Genie Z-40

Бренды по названию

Популярные бренды

Terex Genie Z-40, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание Genie Z-40

Отзывы:

Похожие инструкции для Genie Z-40

Бренды по названию

Популярные бренды