Terex Genie Z-40 Скачать руководство пользователя

Страница: 83 / 287

June 2022

Service and Repair Manual

Manifolds

Part No. 1268555GT

-62/40

8-10 V alve Adjus tme nt - Oscillat e Relief Valve

8-10

Valve Adjustments - Oscillate

Relief Valve

How to Adjust the Oscillate Relief

Valve

Note: Two people will be required to perform this

procedure.
1 Remove the drive chassis cover from the non-

steer end of the machine.

2 Connect a 0 to 2000 psi / 0 to 150 bar

pressure gauge to the diagnostic nipple

located near the oscillate directional valve.

3 Disconnect the directional valve linkage, by

removing the heim joint and retaining fastener

from the axle.

4 Start the engine from the platform controls.

Move the engine idle toggle switch to the high

idle position. Activate the foot switch.

5 With the engine running in high rpm, manually

activate the directional valve linkage in either

direction. Observe the pressure spike on the

pressure gauge when the machine fully

oscillates. Refer to Specifications,

Hydraulic

Component Specifications

6 Turn the engine off.
7 Locate the relief valve on the directional valve

and loosen the jamb nut.

8 Adjust the hex screw. Turn it clockwise to

increase the pressure or counterclockwise to

decrease the pressure. Tighten the jamb nut.

Tip-over hazard. Do not adjust

the relief valve higher than

specified.

9 Repeat steps 4 and 5 to confirm the valve

pressure.

10 Turn the engine off, remove the pressure

gauge and assemble the directional valve

linkage.

11 Install the cover on the non-steer end of the

drive chassis.

Содержание Genie Z-40
































































































































































































































































































Результаты поиска

Содержание Genie Z-40

Отзывы:

Похожие инструкции для Genie Z-40

Бренды по названию

Популярные бренды

Terex Genie Z-40, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание Genie Z-40

Отзывы:

Похожие инструкции для Genie Z-40

Бренды по названию

Популярные бренды