Terex Genie Z-40 Скачать руководство пользователя

Страница: 90 / 287

Service and Repair Manual

June 2022

Manifolds

-62/40

Part No. 1268555GT

8-14 V alve Adjus tme nts, Tr action Ma nifold

8-14

Valve Adjustments - Traction

Manifold

How to Adjust the Charge

Pressure Relief Valve

1 Connect a 0 to 600 psi / 0 to 50 bar pressure

gauge to the test port on the drive pump.

2WD models:

Hold the charge pressure relief

valve located on the traction manifold and

remove the cap (item UU).

4WD models:

Hold the charge pressure relief

valve located on the traction manifold and

loosen the jam nut (item UU).

2WD models:

Turn the internal hex socket

clockwise fully until it stops. Install the cap.

4WD models:

Turn the external stem

clockwise fully until it stops. Tighten the jam

nut.

4 Start the engine and move and hold the

function enable/rpm select toggle switch to

the high rpm (rabbit symbol) position. Note

the reading on the pressure gauge.

5 Turn the engine off.
6 Remove the pressure gauge from the drive

pump. Connect the gauge to the test port

located on the traction manifold.

2WD models:

Hold the charge pressure relief

valve and remove the cap (item UU).

4WD models:

Hold the charge pressure relief

valve and loosen the jam nut. (item UU).

8 Start the engine and move and hold the

function enable/rpm select toggle switch to

the high rpm (rabbit symbol) position.

9 Adjust the relief valve until the pressure

reading on the gauge is 30 psi / 2 bar less

than the pressure reading on the pump. Turn

it clockwise to increase the pressure or

counterclockwise to decrease the pressure.

Install the valve cap or tighten the jam nut.

10 Turn the engine off and remove the pressure

gauge.

Содержание Genie Z-40
































































































































































































































































































Результаты поиска

Содержание Genie Z-40

Отзывы:

Похожие инструкции для Genie Z-40

Бренды по названию

Популярные бренды

Terex Genie Z-40, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание Genie Z-40

Отзывы:

Похожие инструкции для Genie Z-40

Бренды по названию

Популярные бренды