manualshive.com logo in svg

Terex Genie Z-40, Руководство по обслуживанию и ремонту

Поделиться
Скачать
Terex Genie Z-40 Скачать руководство пользователя страница 45

June 2022

 

Service and Repair Manual

 

 

Platform Components

 

 

 

Part No. 1268555GT

 

Z

®

-62/40

 

31 

 

 

 

5  Move the platform up and down by hand, so it 

bounces approximately 2.5 to 5 cm / 1 to 

2 inches. Allow the platform to settle. 

  Result: The overload indicator lights are off 

and the alarm does not sound. Proceed to 

step 6. 

  Result: The overload indicator lights are 

flashing at the platform and ground controls, 

and the alarm is sounding. Slowly tighten the 

load spring adjustment nut in a clockwise 

direction in 10° increments until the overload 

indicator light turns off, and the alarm does 

not sound. Repeat step 5. 

Note: The platform will need to be moved up and 

down and allowed to settle between each 

adjustment. 
Note: There may be a 2 second delay before the 

platform overload indicator light and alarm 

responds. 
6  Turn the key switch to ground controls, pull 

out the red Emergency Stop Button and start 

the engine. 

 

7  Add an additional weight to the platform that 

is equal to, but does not exceed 15% of the 

maximum rated load. 

  Result: The overload indicator light is flashing 

at both the ground and platform controls, the 

alarm is sounding and the engine shuts down. 

Proceed to step 8. 

  Result: The overload indicator lights are off at 

the platform and ground controls, the alarm 

does not sound and the engine continues to 

run. Slowly loosen the load spring adjustment 

nut in a counterclockwise direction in 10° 

increments until the overload indicator light 

flashes at both the platform and ground 

controls, the alarm sounds and the engine 

shuts down. Remove the additional weight. 

Repeat the procedure starting with step 5. 

Note: There may be a 2 second delay before the 

platform overload indicator light and alarm 

responds. 
8  Using auxiliary power, test all machine 

functions from the ground controls. 

  Result: All ground control functions should 

operate. 

9  Using a suitable lifting device, remove the 

additional weight from the platform. 

  Result: The platform overload indicator light 

should be off at both the ground and platform 

controls and the alarm should not sound. 

Note: There may be a 2 second delay before the 

overload indicator lights and alarm turn off. 
10  Start the engine and test all machine 

functions from the ground controls. 

  Result: All ground control functions should 

operate. 

 

Содержание Genie Z-40
































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды