Terex Genie Z-40 Скачать руководство пользователя

Страница: 38 / 287

Service and Repair Manual

June 2022

Platform Controls

-62/40

Part No. 1268555GT

10 Compare the machine function time with the

function times listed in Refer to Specifications,

Performance Specifications

. Determine

whether the function time needs to increase

or decrease.

11 While the joystick is activated, adjust the max-

out setting to achieve the proper function

cycle time. Momentarily move the drive

enable toggle switch in the right direction to

increase the function speed or momentarily

move the drive enable toggle switch in the left

direction to decrease the function speed.

Note: Each time the drive enable toggle switch is

momentarily moved, the function speed will

change in 2% increments.
12 Repeat steps 9 through 11 for each joystick

controlled machine function.

13 Return the joystick to the neutral position and

wait for approximately 10 seconds to allow the

settings to be saved.

Result: The alarm should sound indicating

that the settings have been saved in memory.

Note: Do not operate any machine function during

the 10 second waiting time.

How to Adju st th e Joys tick Ra mp Ra te Setti ng

How to Adjust the Joystick Ramp

Rate Setting

The ramp rate setting of a joystick controls the

time at which it takes for the joystick to reach

maximum output, when moved out of the neutral

position. The ramp rate settings of a joystick can

be changed to compensate for hydraulic pump

wear to maintain peak performance from the

machine.
Note: Perform this procedure with the boom in the

stowed position.
1 Pull out the red Emergency Stop button to the

on position at both the ground and platform

controls.

2 Turn the key switch to platform control. Do not

start the engine.

3 Push in the platform controls red Emergency

Stop button to the off position.

4 Do not press down the foot switch.
5 Move and hold the drive enable toggle switch

in the right position and pull out the red

Emergency Stop button to the on position.

6 When the alarm sounds, release the drive

enable toggle switch.

7 Momentarily activate the drive enable toggle

switch in the right direction 6 times.

Result: There should be a pause and the

alarm should sound 6 times indicating that the

machine is in ramp rate calibration mode.

8 Start the engine from the platform controls

and press down the foot switch.

9 Start a timer and simultaneously move the

joystick in either direction full stroke. Note

how long it takes the function to reach

maximum speed. This is the ramp rate.

Содержание Genie Z-40
































































































































































































































































































Результаты поиска

Содержание Genie Z-40

Отзывы:

Похожие инструкции для Genie Z-40

Бренды по названию

Популярные бренды

Terex Genie Z-40, Руководство по обслуживанию и ремонту

Результаты поиска

Содержание Genie Z-40

Отзывы:

Похожие инструкции для Genie Z-40

Бренды по названию

Популярные бренды